With this panel, all the LEDs of the Phoenix Charger and the actual charge current can be read. In addition, the maximum charging current can be limited. This is especially useful when the mains voltage is protected by a low amperage.The panel (not included) connected with a commercially available UTP cable.The brightness of the LEDs is adjusted automatically to the ambient light.
Adaptive four-stage charge characteristic: bulk - absorption - float - storage. The microprocessor-controlled "adaptive" battery management system can be adapted to different types of batteries. The adaptive feature will automatically optimize the process relative to the way the battery.Two outputs, each with full output current, for the simultaneous charge of two battery packs. Each output provides the full current.Additional output (4 A) to maintain the charge of the starter battery.The right amount of charge: variable absorption time.At low battery discharge, a short absorption is chosen to avoid overcharging and excessive gas development. After a deep discharge the absorption time is automatically extended to be able to fully charge the battery.The charger switches to Phoenix "storage" if more than 24 hours there is no discharge. The voltage is then reduced to 2.2 V / cell (13.2 V for a 12 V battery). In the battery then hardly gassing and corrosion of the positive plates is limited to a minimum. Once aWeek the voltage is increased to the absorption level to recharge the battery. Prevents stratification of the electrolyte and prevent sulfation.To increase battery life: temperature compensation. Every Phoenix charger, a temperature sensor is included. The temperature sensor provides a decreasing charge voltage with increasing battery temperature. This is particularly important for maintenance-free batteries, which otherwisethreaten to dry out by overcharging.Voltage sensor (voltage sense): measuring the charging voltage directly on the battery or the DC distribution. To compensate for voltage loss due to the resistance of the charging cable, the Phoenix have chargers via a "Voltage Sense" function. It ensures that theBattery always receives the correct charge voltageInput voltage: 90-265 VAC, 45-65 Hz / 90-400 V DCCharging voltage -absorption-: 14.4 V DCFloat voltage: 13.8 V DCStorage Mode: 13.2 V DCCharge current house battery: 50 ACharging current starter battery: 4 ACharging characteristics: 4 steps adaptivelyBattery capacity: 200 to 800 AhTemperature sensor: yesCan be used as power supply: yesCooling (active): yesProtection: short circuit, battery reverse polarity detection, Battery voltage too high, too high a temperatureOperating temperature range: -20 to 60 ° C max, Rel humidity.. 95%Battery connections: M6 boltAC connection: screw terminal 4 mm² (AWG6)Protection: IP21Weight: 3,8 kgDimensions (HxBxT): 350 x 200 x 108 mm
€631.18*
€788.97*(20% saved vs. recommended price)
Adaptive four-stage charge characteristic: bulk - absorption - float - storage. The microprocessor-controlled "adaptive" battery management system can be adapted to different types of batteries. The adaptive feature will automatically optimize the process relative to the way the battery.Two outputs, each with full output current, for the simultaneous charge of two battery packs. Each output provides the full current.Additional output (4 A) to maintain the charge of the starter battery.The right amount of charge: variable absorption time.At low battery discharge, a short absorption is chosen to avoid overcharging and excessive gas development. After a deep discharge the absorption time is automatically extended to be able to fully charge the battery.The charger switches to Phoenix "storage" if more than 24 hours there is no discharge. The voltage is then reduced to 2.2 V / cell (13.2 V for a 12 V battery). In the battery then hardly gassing and corrosion of the positive plates is limited to a minimum. Once aWeek the voltage is increased to the absorption level to recharge the battery. Prevents stratification of the electrolyte and prevent sulfation.To increase battery life: temperature compensation. Every Phoenix charger, a temperature sensor is included. The temperature sensor provides a decreasing charge voltage with increasing battery temperature. This is particularly important for maintenance-free batteries, which otherwisethreaten to dry out by overcharging.Voltage sensor (voltage sense): measuring the charging voltage directly on the battery or the DC distribution. To compensate for voltage loss due to the resistance of the charging cable, the Phoenix have chargers via a "Voltage Sense" function. It ensures that theBattery always receives the correct charge voltageInput voltage: 90-265 VAC, 45-65 Hz / 90-400 V DCCharging voltage -absorption-: 28.8 V DCFloat voltage: 27.6 V DCStorage Mode: 26.4 V DCCharge current house battery: 25 ACharging current starter battery: 4 ACharging characteristics: 4 steps adaptivelyBattery capacity: 100 - 400 AhTemperature sensor: yesCan be used as power supply: yesCooling (active): yesProtection: short circuit, battery reverse polarity detection, Battery voltage too high, too high a temperatureOperating temperature range: -20 to 60 ° C max, Rel humidity.. 95%Battery connections: M6 boltAC connection: screw terminal 4 mm² (AWG6)Protection: IP21Weight: 3,8 kgDimensions (HxBxT): 350 x 200 x 108 mm
€631.18*
€788.97*(20% saved vs. recommended price)
Adaptive four-stage charge characteristic: bulk - absorption - float - storage. The microprocessor-controlled "adaptive" battery management system can be adapted to different types of batteries. The adaptive feature will automatically optimize the process relative to the way the battery.Two outputs, each with full output current, for the simultaneous charge of two battery packs. Each output provides the full current.Additional output (4 A) to maintain the charge of the starter battery.The right amount of charge: variable absorption time.At low battery discharge, a short absorption is chosen to avoid overcharging and excessive gas development. After a deep discharge the absorption time is automatically extended to be able to fully charge the battery.The charger switches to Phoenix "storage" if more than 24 hours there is no discharge. The voltage is then reduced to 2.2 V / cell (13.2 V for a 12 V battery). In the battery then hardly gassing and corrosion of the positive plates is limited to a minimum. Once aWeek the voltage is increased to the absorption level to recharge the battery. Prevents stratification of the electrolyte and prevent sulfation.To increase battery life: temperature compensation. Every Phoenix charger, a temperature sensor is included. The temperature sensor provides a decreasing charge voltage with increasing battery temperature. This is particularly important for maintenance-free batteries, which otherwisethreaten to dry out by overcharging.Voltage sensor (voltage sense): measuring the charging voltage directly on the battery or the DC distribution. To compensate for voltage loss due to the resistance of the charging cable, the Phoenix have chargers via a "Voltage Sense" function. It ensures that theBattery always receives the correct charge voltageInput voltage: 90-265 VAC, 45-65 Hz / 90-400 V DCCharging voltage -absorption-: 14.4 V DCFloat voltage: 13.8 V DCStorage Mode: 13.2 V DCCharge current house battery: 30 ACharging current starter battery: 4 ACharging characteristics: 4 steps adaptivelyBattery capacity: 100 to 400 AhTemperature sensor: yesCan be used as power supply: yesCooling (active): yesProtection: short circuit, battery reverse polarity detection, Battery voltage too high, too high a temperatureOperating temperature range: -20 to 60 ° C max, Rel humidity.. 95%Battery connections: M6 boltAC connection: screw terminal 4 mm² (AWG6)Protection: IP21Weight: 3,8 kgDimensions (HxBxT): 350 x 200 x 108 mm
€473.14*
€591.43*(20% saved vs. recommended price)
Adaptive four -stage charging characteristic: Bulk - absorption - Float - storage. The microprocessor-controlled "adaptive" battery management system can be matched to various battery types. The adaptive function automatically adjusts the charging process to the use of the battery.Two outputs, each with a full output current, for the simultaneous load of two batteries. Each output delivers the full current.Additional output (4 a) for cargo maintenance for starter battery.The correct charge quantity: adapted absorption time.With a low battery discharge, a short absorption is chosen to avoid overload and excessive gas development. After a deep discharge, the absorption period is automatically extended in order to be able to load the battery in full.The Phoenix charger switches to “storage” if there is no discharge for more than 24 hours. The voltage is then reduced to 2.2 V / cell (13.2 V for a 12-V battery). Hardly any gas develops in the battery and the corrosion of the anode plates is limited to a minimum. Once aWeek increases the tension to the absorption level to recharge the battery. This prevents layer formation in electrolyte and sulfuring.Higher battery life due to temperature compensation. A temperature sensor is included for each Phoenix charger. The temperature sensor ensures a decreasing charging voltage with increasing battery temperature. This is particularly important for maintenance -free batteries that otherwisethreaten to dry out overload.Tension sensor (Voltage Sense): Measure the charging voltage directly on the battery or on the DC distributor. To compensate for voltage losses as a result of the resistance of the charging cables, the Phoenix chargers have a "Voltage Sense" function. It ensures that theBattery receives the correct charging voltage at any timeInput voltage: 90–265 V AC, 45-65 Hz / 90-400 V DCCharging tension -absorption-: 28.8 V DCConservation voltage: 27.6 V DCStorage fashion: 26.4 V DCCharging current on -board net battery: 16 aCharging current starter battery: 4 aCharging characteristics: 4 steps adaptiveBattery capacity: 100 - 200 AhTemperature sensor: YesCan be used as a power supply: yesCooling (active): YesProtection: Short circuit, battery solving recognition, too high battery voltage, too high temperatureOperating temperature range: -20 to 60 ° C, rel. Air humidity max. 95 %Battery connections: M6 boltsAC connection: screw clamp 4 mm² (AWG6)Protection class: IP21Weight: 3.8 kgDimensions (HXBXT): 350 x 200 x 108 mm
€473.14*
€591.43*(20% saved vs. recommended price)
This website uses cookies to ensure the best experience possible.