Victron - Phoenix Smart IP43 Charger 12/30 (1+1)
€382.40*
% €449.82* (14.99% saved vs. recommended price)will be ordered for you
Lead time: 7 days (according to manufacturer**),
est. total delivery time: 1-2 weeks
Product number:
1973796
EAN:
8719076041900
Manufacturer product ID:
PSC123051085
Please note that our English product descriptions are automatic translations from German. If anything is unclear, please contact us and/or double check the description by the manufacturer. Thanks for your understanding! - your Klabauter Crew
Product information "Victron - Phoenix Smart IP43 Charger 12/30 (1+1)"
Phoenix Smart IP43 charger
12 V, 2 outputs 12/30 (1+1)
Ready for Bluetooth Smart
Change the settings and updating the charger for newly available software functions can be carried out with any Bluetooth-enabled smartphone, tablet or other device.
Phoenix Smart (1+1): Two outputs for charging two batteries
The second output is intended for charging the starter battery. As a result, it is limited to 3 A and has a slightly lower output voltage for keeping loading the usually full starter battery.
Automatic voltage compensation
The charger compensates for a voltage drop on the DC cables by slightly increasing the output voltage when the direct current increases.
You can find more details in the manual.
Adaptive five-stage loading algorithm: constant current-(“Bulk”) phase, constant voltage-(“absorption”) phase, restoration (“recondition”) phase, load maintenance voltage-(“float”) phase, warehouse voltage-(“storage”) phase:
The Phoenix Smart charger has our well-known "adaptive" battery management system, which can be matched to the different types of battery. “Adaptive” means that the charging characteristic is automatically adjusted to the type of battery use.
The correct amount of charging: variable constant stress phase
With a low battery discharge (e.g. a yacht connected to country current), a short constant voltage phase is chosen to avoid an overload.
After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged.
Prevention of damage caused by excessive gastung: Batterysafe mode (see Figure 2)
In order to shorten the loading time, the highest possible charging current was selected together with a high constant voltage.
However, in order for an excessive gas development to be avoided towards the end of the constant trump phase, the charger limits the speed of the voltage increase after the gas voltage has been reached.
Less maintenance and aging in the resting state of the battery: the storage mode
The warehouse mode is always activated if no discharge has been carried out within 24 hours.
In storage mode, the loading voltage is then reduced to 2.2 V/cell (13.2 V for a 24 V battery) in order to minimize gas development and corrosion on the positive plates.
Once a week, the voltage is increased to the level of the gas voltage.
This achieves a kind of compensation charge that prevents the electrolystic layering and sulfating - the two main reasons for premature battery failure.
Lithium ions (LIFEPO4) also loads batteries
A/off control can be installed by connecting a relay or an optocoupler output with an open collector by a Li-ion BMS to a remote-controlled one/output port.
Alternatively, voltage and electricity can also be ruled completely via Bluetooth.
Fully programmable charging algorithm
The loading algorithm can be programmed via Bluetooth or via VE.Direct interface.
With the Mode button, you can choose between three pre -programmed algorithms (see technical information).
Remote on/off
The remote on/off consists of two terminals: Remote H and Remote L.
A remote/exterior switch or relay contact can be connected between H and L.
Alternatively, the terminal H can be pulled up or the Terminal L can be pulled down.
See manual for details.
Ve.direct interface
For a wired data connection with a color control panel, a PC or other devices.
Note the VictronConnect app under Downloads/Software on Victron Energy website.
Programmable relay
Can be programmed via the VE.Direct interface or a Bluetooth-compatible device to trigger an alarm or other events.
Technical specifications:
Input voltage 230 VAC (area 210-250 V)
DC input voltage range 290-355 VDC
Frequency 45/-65 Hz
Power factor 0.7
Deduction Return current AC separated: <0.1 MA AC connected and remote control charger: <6 ma
Electricity consumption without load 1 w
Effect 94%
"Constant" charging voltage (absorption): Normal: 14.4 V / high: 14.7V / lithium ions: 14.2 V
"Conservation" charging voltage (float): normal: 13.8 V / high: 13.8V / lithium ion: 13.5 V
Storage mode: normal: 13.2V / high: 13.2V / lithium ion: 13.5 V
Charging current house battery 30 a
Low power mode 15 a
Charging current starter battery 3 a
Ladeal gorithm five stages, adaptive
Protection: Polation on battery (backup, not accessible by the user) / output cocoing / over temperature
Can be used as a power supply: Yes, output voltage can be set with Bluetooth and/or Ve.direct.
Operating temperature range -20 to 60? (0 - 140 f) - nominal output current up to 40 ° C, deteriorated linearly to 20 % at 60 ° C
Moist (non -condensing) max 95 %
Relay (programmable) DC Nodble value: 5 A up to 28 VDC
Battery connection screw terminals 16 mm² (AWG6)
AC connection: IEC 320 C14 input with bracket (AC cable with a country-specific connector must be ordered separately.)
Protection class IP43 (electronic components), IP22 (connection area)
Weight 3.5 kg
Dimensions (HXBXT) 180 x 249 x 100 mm
AC network cable (1973806) Please order separately!
12 V, 2 outputs 12/30 (1+1)
Ready for Bluetooth Smart
Change the settings and updating the charger for newly available software functions can be carried out with any Bluetooth-enabled smartphone, tablet or other device.
Phoenix Smart (1+1): Two outputs for charging two batteries
The second output is intended for charging the starter battery. As a result, it is limited to 3 A and has a slightly lower output voltage for keeping loading the usually full starter battery.
Automatic voltage compensation
The charger compensates for a voltage drop on the DC cables by slightly increasing the output voltage when the direct current increases.
You can find more details in the manual.
Adaptive five-stage loading algorithm: constant current-(“Bulk”) phase, constant voltage-(“absorption”) phase, restoration (“recondition”) phase, load maintenance voltage-(“float”) phase, warehouse voltage-(“storage”) phase:
The Phoenix Smart charger has our well-known "adaptive" battery management system, which can be matched to the different types of battery. “Adaptive” means that the charging characteristic is automatically adjusted to the type of battery use.
The correct amount of charging: variable constant stress phase
With a low battery discharge (e.g. a yacht connected to country current), a short constant voltage phase is chosen to avoid an overload.
After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged.
Prevention of damage caused by excessive gastung: Batterysafe mode (see Figure 2)
In order to shorten the loading time, the highest possible charging current was selected together with a high constant voltage.
However, in order for an excessive gas development to be avoided towards the end of the constant trump phase, the charger limits the speed of the voltage increase after the gas voltage has been reached.
Less maintenance and aging in the resting state of the battery: the storage mode
The warehouse mode is always activated if no discharge has been carried out within 24 hours.
In storage mode, the loading voltage is then reduced to 2.2 V/cell (13.2 V for a 24 V battery) in order to minimize gas development and corrosion on the positive plates.
Once a week, the voltage is increased to the level of the gas voltage.
This achieves a kind of compensation charge that prevents the electrolystic layering and sulfating - the two main reasons for premature battery failure.
Lithium ions (LIFEPO4) also loads batteries
A/off control can be installed by connecting a relay or an optocoupler output with an open collector by a Li-ion BMS to a remote-controlled one/output port.
Alternatively, voltage and electricity can also be ruled completely via Bluetooth.
Fully programmable charging algorithm
The loading algorithm can be programmed via Bluetooth or via VE.Direct interface.
With the Mode button, you can choose between three pre -programmed algorithms (see technical information).
Remote on/off
The remote on/off consists of two terminals: Remote H and Remote L.
A remote/exterior switch or relay contact can be connected between H and L.
Alternatively, the terminal H can be pulled up or the Terminal L can be pulled down.
See manual for details.
Ve.direct interface
For a wired data connection with a color control panel, a PC or other devices.
Note the VictronConnect app under Downloads/Software on Victron Energy website.
Programmable relay
Can be programmed via the VE.Direct interface or a Bluetooth-compatible device to trigger an alarm or other events.
Technical specifications:
Input voltage 230 VAC (area 210-250 V)
DC input voltage range 290-355 VDC
Frequency 45/-65 Hz
Power factor 0.7
Deduction Return current AC separated: <0.1 MA AC connected and remote control charger: <6 ma
Electricity consumption without load 1 w
Effect 94%
"Constant" charging voltage (absorption): Normal: 14.4 V / high: 14.7V / lithium ions: 14.2 V
"Conservation" charging voltage (float): normal: 13.8 V / high: 13.8V / lithium ion: 13.5 V
Storage mode: normal: 13.2V / high: 13.2V / lithium ion: 13.5 V
Charging current house battery 30 a
Low power mode 15 a
Charging current starter battery 3 a
Ladeal gorithm five stages, adaptive
Protection: Polation on battery (backup, not accessible by the user) / output cocoing / over temperature
Can be used as a power supply: Yes, output voltage can be set with Bluetooth and/or Ve.direct.
Operating temperature range -20 to 60? (0 - 140 f) - nominal output current up to 40 ° C, deteriorated linearly to 20 % at 60 ° C
Moist (non -condensing) max 95 %
Relay (programmable) DC Nodble value: 5 A up to 28 VDC
Battery connection screw terminals 16 mm² (AWG6)
AC connection: IEC 320 C14 input with bracket (AC cable with a country-specific connector must be ordered separately.)
Protection class IP43 (electronic components), IP22 (connection area)
Weight 3.5 kg
Dimensions (HXBXT) 180 x 249 x 100 mm
AC network cable (1973806) Please order separately!