Victron - Phoenix

This model is an efficient and reliable inverter.It joins our pallet of the proven and tested Phoenix inverters and is now available in a slimmer design and a all -metal housing.There are 1600 VA, 2000 VA and 3000 VA models for 12, 24 or 48 V systems.Its performance is enough to supply most devices with plugs in your vehicle, boat, motorhome or at home.A ring transformer offers the possibility of supply even with high performance peaks, a stable voltage, frequency and a high-quality sine wave.The installation is even easier than ever: the connections are even easier for the installer, which gives you an even more professional result.Built-in Bluetooth function: Fully configurable via a tablet or smartphone:• Alarm low battery voltage• Swaving values for switching off and restarting at low battery voltage values.• Dynamic switching off: load-dependent switch-off threshold value• Output voltage: 210 - 245V• Frequency: 50 Hz or 60 Hz• threshold value for ECO mode on/off and ECO mode sensor• Alarm relaysMonitoring:• Input and output voltage, load and alarmsVe.direct communication connectionThe VE.Direct Port can be connected to a computer (a VE.Direct for usbinterface cable is required) to configure and monitor the same parameters.Proven reliabilityThe complete bridging with a ring transformer panel has proven itself for years.The inverters are short -circuit -resistant and protected against overheating (whether caused by overload or by the ambient temperature).High switch -on performanceThis is required to switch on loads such as voltage formers for leather lamps, halogen lamps or power tools.Eco modeIn ECO mode, the inverter switches to standby as soon as the load drops under a preset value.In standby mode, the inverter then switches on every 2.5 seconds for a short period of time (can be regulated).If the load exceeds the preset threshold value, the inverter remains on.Remote-controlled input/outputA remote-controlled on/off switch or a relay contact can be connected to the two-pin connector.Alternatively, the connection H (left) of the two-pole connector can be switched to a battery plus pole or the connection l (right) of the two-pole plug to the battery minus pole (or for example to the body of a vehicle).Input voltage range 18.6 - 34 VOutput output voltage: 230 VAC ± 2 % 50 Hz or 60 Hz ± 0.1 % (1)Account. Output power at 25 ° C 3000VAAccount. Output power at 25 ° C 2400WAccount. Output power at 40 ° C 2200WAccount. Output power at 65 ° C 1700WTop performance 6000VADynamic (load -dependent) shutdown due to low DC (fully configurable)Switch off dynamic, see https://www.victronenergy.com/live/ve.direct:phoenix-inverters-dynamic-cutoffMax. Effect 94 %Zero-load performance 13WZero-load performance in ECO mode 1.9WProgrammable relay (2) yesStop & start performance ECO mode can be adjustedProtection (3) a - GWireless Bluetooth communication for remote monitoring and system integrationVe.direct Communication connection for remote monitoring and system integrationRemote-controlled insert/off circuit yesCommon features of the operating temperature range: -40 to +65 ° C (blower testing)Moist (not condensing): max. 95 %Material & color: steel (blue RAL 5012; and black RAL 9017) Protection class: IP 21Battery connection 2+2 M8 bolts230 V AC connection screw terminalsWeight 19kgDimensions (HXBXT) 485 x 285 x 150 mm

VE.Direct communication portThe VE.Direct port can be connected to the following devices:- (required VE.Direct to USB interface cable) to a computer- With Apple and Android smartphones, tablets, Macbooks and other devices(Smart VE.Direct Bluetooth dongle required).Fully configurable:- threshold values

VE.Direct communication portThe VE.Direct port can be connected to the following devices:- (required VE.Direct to USB interface cable) to a computer- With Apple and Android smartphones, tablets, Macbooks and other devices(Smart VE.Direct Bluetooth dongle required).Fully configurable:- threshold values

Ve.direct communication connectionThe VE.Direct connection can be connected to the following devices:-With a computer (Ve.direct to USB interface cable required)- With Apple and Android smartphones, tablets, macbooks or other devices(Ve.direct Bluetooth Smart Dongle required).Fully configurable:- threshold values for triggering and resetting alarms with a low loading status of the battery.- swelling values for switching off and restarting at low battery voltage values.- Dynamic switching off: load-dependent switch-off threshold value- Output voltage 210-245V- Frequency 50Hz or 60Hz-threshold value for ECO mode on/off and Eco mode sensorMonitoring:- and output voltage, % load and alarmsProven reliabilityThe complete bridging with a ring transformer panel has proven itself for years.The inverters are short -circuit -resistant and before overheating (whether by overloading or by theAmbient temperature caused).High switch -on performanceThis is used to switch on loads such as voltage formers for LED-Lamps, halogen lamps or electric tools.Eco modeIn ECO mode, the inverter switches to standby as soon as the load under a preset valuedrops off. In standby mode, the inverter then switches on for a short period of time (regulatedStandard setting: every 2.5 seconds). If the load exceeds a preset threshold, remainsthe inverter switched on.Remote-controlled input/outputA remote-controlled insertion/off switch can be used with a two-pin connector or between the plus pole of theConnect the battery and the left contact of the two -pin connector.LED diagnosisPlease note the description in the manual.Load switching on another changeover of alternating current: the automatic transfer switchWe recommend our Filax Automatic Transfer Switch for our low-performance inverter. With theFilax is switched very quickly (in less than 20 milliseconds), so that an interruption -freeOperation of computers and other electronic devices is guaranteed.

The ultra-fast transfer switch Filax was developed with the goal of sensitive electronics, such as switch computers or modern entertainment system from an AC power source to another. Main power source is typically the power grid, a generator or a land connection. As an alternative source, an inverter is used usually. With its switching time of less than 20 milliseconds even sensitive loads continue to work without interruption. The Filax is not adapted to domestic appliances, with a high power consumption, such as e.g. to provide washing machines or electric motors.230 V / 50 Hz, the maximum switching power 3500 W. dimensions (W): 200 x 120 x 75 mm.

Phoenix Inverter ControlThis control panel is suitable for Phoenix inverters equipped with a UTP remote monitoring and a socket for control panels. In addition, it can with a MutiPlus inverter / charger be used if indeed an automatic transfer switch function but no charger function is desired. The brightness of the LEDs is automatically reduced during the night. Dimensions (HxWxD): 65 x 60 x 40 mm.Only for the following models: 12/1200, 12/1600, 12/2000, 12/3000, 12/5000, 24/1200, 24/1600, 24/2000, 24/3000, 24/5000, 48/3000 and 48 / 5000th

The Phoenix inverter series was developed for commercial use; It is suitable for a variety of applications. The development aimed uncompromisingly on an inverter with a clean sinus output with high efficiency.An essential feature is the particularly high starting performance. Phoenix inverters are able to cope with the high starting streams, for example, of cooling compressors, tool engines and the like.Practically unlimited performance through parallel circuit and three-phase operation. Up to six inverter units can be switched in parallel to increase performance. Six 24/5000 units can be handed in e.g. 24kW / 30KVA power. A three-phase operation is also possible.Computer interfaces: All models have an RS-485 access. You only need our MK2 interface (see also under accessories). This interface takes over the galvanic separation between the inverter and the computer and converted from RS-485 to RS-232. An RS-232 to USB conversion cable is also available. With the Veconfigure software, which can be downloaded free of charge, the inverters can be adjusted as required. This includes the output voltage and frequency, the upper and lower voltage limits and the programming of the relay. The relay can be used, for example, to create signals in special situations or to start a generator.- Phoenix inverter type: 48/3000- Parallel and 3-phase operation: Yes- Area of input voltage (VDC): 38–66 V- Exit: Output: 230 V ± 2 %, frequency: 50 Hz ± 0.1 % (can also be set to 60 Hz, and 240 V)- Output period at 25 ºC (VA)*: 3000- Output duration performance 25 ºC (W): 2500- Output duration performance 40 ºC (W): 2200- Peakpower (W): 6000- Max. Efficiency (%): 95- Nullllast (w): 16- Nullllast in AES-Mode (W): 12- Neulllast in search mode (w): 5- protection: short circuit at the output, overload, battery voltage too high, battery voltage too low, temperature too high, 230 V AC at the inverter output, too high humming voltage at the input-Features: operating temperature: -20 to +50 ° C (fan cooling), type of protection: IP21- Battery connection: 2+2 M8 bolts-230V AC connection: screw connection- Weight (kg): 18- Dimensions (HXBXT in mm): 362x258x218- *Top factor with non -linear load 3: 1

The Phoenix inverter series was developed for commercial use: clean sine output with high efficiency + high starting performance.They can cope with high start -up flows, for example, of cooling compressors, tool engines and the like.Practically unlimited performance by circuit of up to 6 units (e.g. 24 kW / 30KVA power can hand in) and three-phase operation. sixComputer interfaces with RS-485 access. You only need our MK2 interface (see also under accessories). This interface takes over the galvanic separation between the inverter and the computer and converted from RS-485 to RS-232. An RS-232 to USB conversion cable is also available.With the Veconfigure software (downloadable free of charge), the inverters can be adjusted as required:Output voltage and frequencyUpper and lower voltage limitsProgramming the relay (e.g. for creating signals in special situations or the start of a generator)- Phoenix inverter type: 24/3000- Parallel and 3-phase operation: Yes- Area of input voltage (VDC): 19–33 V- Exit: Output: 230 V ± 2 %, frequency: 50 Hz ± 0.1 % (can also be set to 60 Hz, and 240 V)- Output period at 25 ºC (VA)*: 3000- Output period at 25 ºC (W): 2500- Output period at 40 ºC (W): 2200- Peakpower (W): 6000- Max. Efficiency (%): 94- Nullllast (w): 15- Nullllast in AES-Mode (W): 10- Neulllast in search mode (w): 5- protection: short circuit at the output, overload, battery voltage too high, battery voltage too low, temperature too high, 230 V AC at the inverter output, too high humming voltage at the input-Features: operating temperature: -20 to +50 ° C (fan cooling), type of protection: IP21- Battery connection: 2+2 M8 bolts-230V AC connection: screw connection- Weight (kg): 18- Dimensions (HXBXT in mm): 362x258x218- *Top factor with non -linear load 3: 1

The Phoenix inverter series was developed for commercial use; It is suitable for a variety of applications. The development aimed uncompromisingly on an inverter with a clean sinus output with high efficiency.An essential feature is the particularly high starting performance. Phoenix inverters are able to cope with the high starting streams, for example, of cooling compressors, tool engines and the like.Practically unlimited performance through parallel circuit and three-phase operation. Up to six inverter units can be switched in parallel to increase performance. Six 24/5000 units can be handed in e.g. 24kW / 30KVA power. A three-phase operation is also possible.Computer interfaces: All models have an RS-485 access. You only need our MK2 interface (see also under accessories). This interface takes over the galvanic separation between the inverter and the computer and converted from RS-485 to RS-232. An RS-232 to USB conversion cable is also available. With the Veconfigure software, which can be downloaded free of charge, the inverters can be adjusted as required. This includes the output voltage and frequency, the upper and lower voltage limits and the programming of the relay. The relay can be used, for example, to create signals in special situations or to start a generator.- Phoenix inverter type: 12/3000- Parallel and 3-phase operation: Yes- Area of input voltage (VDC): 9.5–17 V- Exit: Output: 230 V ± 2 %, frequency: 50 Hz ± 0.1 % (can also be set to 60 Hz, and 240 V)- Output period at 25 ºC (VA)*: 3000- Output duration performance 25 ºC (W): 2500- Output duration performance 40 ºC (W): 2200- Peakpower (W): 6000- Max. Efficiency (%): 93- Nullllast (w): 15- Nullllast in AES-Mode (W): 10- Neulllast in Search-Mode (W): 4-protection: Short circuit at the output, overload, battery voltage too high, battery voltage too low, temperature too high, 230 V AC at the inverter output, too high humming voltage at the input-Features: operating temperature: -20 to +50 ° C (fan cooling), type of protection: IP21- Battery connection: 2+2 M8 bolts-230V AC connection: screw connection- Weight (kg): 18- Dimensions (HXBXT in mm): 362x258x218- *Top factor with non -linear load 3: 1

VE.Direct communication portThe VE.Direct port can be connected to the following devices:- (required VE.Direct to USB interface cable) to a computer- With Apple and Android smartphones, tablets, Macbooks and other devices(Smart VE.Direct Bluetooth dongle required).Fully configurable:- threshold values

The Phoenix Compact Inverter series has been developed for commercial use; it is suitable for a variety of applications. The development but without compromise on an inverter with clean sine wave output with high efficiency.A key feature is very high start performance. Phoenix inverters are capable of the high starting currents, for example, of refrigeration compressors, electric motors and similar appliances.Virtually unlimited power thanks to parallel and three-phase operation. Up to six inverter units can be connected in parallel for increased performance. Six 24/5000 units, for example, Make 24kW / 30kVA power. A three-phase operation is also possible.Computer Interfaces: All models have a RS-485 connection. All you need is our MK2 interface (see under accessories). This interface takes care of galvanic isolation between the inverter and the computer, and converts from RS-485 to RS-232. An RS-232 to USB conversion cable is also available. With the VEConfigure software that is downloaded for free, the inverters can be adjusted according to requirements. This includes output voltage and frequency, the upper and lower voltage limits and the programming of the relay. The relay can, for example, for generating signals in special situations or can be also used to start a generator.- Phoenix Inverter Type: C24 / 2000- Parallel and 3-phase operation: Yes- Input voltage (VDC): 19-33 V- Output: Output: 230 V ± 2%, frequency: 50 Hz ± 0.1% (may also be set to 60 Hz, and 240 V)- output power at 25 ° C (VA) *: 2000- Ausgangsdauerleistungbei25 ° C (W): 1600- Ausgangsdauerleistungbei40 ° C (W) 1450- Peak Power (W): 4000- Max efficiency (%): 94th- zero load (W): 11- no-load in AES mode (W): 9- no-load in Search mode (W): 3- Protection: Output short circuit, overload, battery voltage too high, battery voltage too low, too high temperature, 230 V AC at the inverter output, too high input voltage ripple- Description: Operating Temperature: -20 to +50 ° C (cooling fan) Protection: IP21- Battery connection: M8 bolts- 230V AC Connection: spring clamp- Weight (kg): 12- Dimensions (HxWxD in mm): 520x255x125- * Crest factor with non-linear load 3: 1

The Phoenix Compact Inverter series has been developed for commercial use; it is suitable for a variety of applications. The development but without compromise on an inverter with clean sine wave output with high efficiency.A key feature is very high start performance. Phoenix inverters are capable of the high starting currents, for example, of refrigeration compressors, electric motors and similar appliances.Virtually unlimited power thanks to parallel and three-phase operation. Up to six inverter units can be connected in parallel for increased performance. Six 24/5000 units, for example, Make 24kW / 30kVA power. A three-phase operation is also possible.Computer Interfaces: All models have a RS-485 connection. All you need is our MK2 interface (see under accessories). This interface takes care of galvanic isolation between the inverter and the computer, and converts from RS-485 to RS-232. An RS-232 to USB conversion cable is also available. With the VEConfigure software that is downloaded for free, the inverters can be adjusted according to requirements. This includes output voltage and frequency, the upper and lower voltage limits and the programming of the relay. The relay can, for example, for generating signals in special situations or can be also used to start a generator.- Phoenix Inverter Type: C24 / 1600- Parallel and 3-phase operation: Yes- Input voltage (VDC): 19-33 V- Output: Output: 230 V ± 2%, frequency: 50 Hz ± 0.1% (may also be set to 60 Hz, and 240 V)- output power at 25 ° C (VA) *: 1600- Ausgangsdauerleistungbei25 ° C (W): 1300- Ausgangsdauerleistungbei40 ° C (W): 1200- Peak Power (W): 3000- Max efficiency (%): 94th- zero load (W): 10- no-load in AES mode (W): 8- no-load in Search mode (W): 3- Protection: Output short circuit, overload, battery voltage too high, battery voltage too low, too high temperature, 230 V AC at the inverter output, too high input voltage ripple- Description: Operating Temperature: -20 to +50 ° C (cooling fan) Protection: IP21- Battery connection: battery cable included 1.5 meters- 230V AC connection: G-ST18i connector- Weight (kg): 10- Dimensions (HxWxD in mm): 375x214x110- * Crest factor with non-linear load 3: 1

The Phoenix Compact inverter series was developed for commercial use; It is suitable for a variety of applications. The development aimed uncompromisingly on an inverter with a clean sinus output with high efficiency.An essential feature is the particularly high starting performance. Phoenix inverters are able to cope with the high starting streams, for example, of cooling compressors, tool engines and the like.Practically unlimited performance through parallel circuit and three-phase operation. Up to six inverter units can be switched in parallel to increase performance. Six 24/5000 units can be handed in e.g. 24kW / 30KVA power. A three-phase operation is also possible.Computer interfaces: All models have an RS-485 access. You only need our MK2 interface (see also under accessories). This interface takes over the galvanic separation between the inverter and the computer and converted from RS-485 to RS-232. An RS-232 to USB conversion cable is also available. With the Veconfigure software, which can be downloaded free of charge, the inverters can be adjusted as required. This includes the output voltage and frequency, the upper and lower voltage limits and the programming of the relay. The relay can be used, for example, to create signals in special situations or to start a generator.- Phoenix inverter type: C12/2000- Parallel and 3-phase operation: Yes- Area of input voltage (VDC): 9.5–17 V- Exit: Output: 230 V ± 2 %, frequency: 50 Hz ± 0.1 % (can also be set to 60 Hz, and 240 V)- Output period at 25 ºC (VA)*: 2000- Output duration performance 25 ºC (W): 1600- Output duration performance 40 ºC (W): 1450- Peakpower (W): 4000- Max. Efficiency (%): 92- Nullllast (W): 9- Nullllast in AES-Mode (W): 7- Nulllast in Search-Mode (W): 3- Protection: Short circuit at the output, overload, battery voltage too high, battery voltage too low, temperature too high, 230 V AC at the inverter output, too high humming tension at the input-Features: operating temperature: -20 to +50 ° C (fan cooling), type of protection: IP21- Battery Connection: M8 Bolzen- 230V AC connection: feather clamp- Weight (kg): 12- Dimensions (HXBXT in mm): 520x255x125- *Top factor with non -linear load 3: 1

The Phoenix Compact inverter series was developed for commercial use; It is suitable for a variety of applications. The development aimed uncompromisingly on an inverter with a clean sinus output with high efficiency.An essential feature is the particularly high starting performance. Phoenix inverters are able to cope with the high starting streams, for example, of cooling compressors, tool engines and the like.Practically unlimited performance through parallel circuit and three-phase operation. Up to six inverter units can be switched in parallel to increase performance. Six 24/5000 units can be handed in e.g. 24kW / 30KVA power. A three-phase operation is also possible.Computer interfaces: All models have an RS-485 access. You only need our MK2 interface (see also under accessories). This interface takes over the galvanic separation between the inverter and the computer and converted from RS-485 to RS-232. An RS-232 to USB conversion cable is also available. With the Veconfigure software, which can be downloaded free of charge, the inverters can be adjusted as required. This includes the output voltage and frequency, the upper and lower voltage limits and the programming of the relay. The relay can be used, for example, to create signals in special situations or to start a generator.- Phoenix inverter type: C12/1600- Parallel and 3-phase operation: Yes- Area of input voltage (VDC): 9.5–17 V- Exit: Output: 230 V ± 2 %, frequency: 50 Hz ± 0.1 % (can also be set to 60 Hz, and 240 V)- Output period at 25 ºC (VA)*: 1600- Output duration performance 25 ºC (W): 1300- Output duration performance 40 ºC (W): 1200- Peakpower (W): 3000- Max. Efficiency (%): 92- Nullllast (W): 8- Nullllast in AES-Mode (W): 5- Nulllast in Search-Mode (W): 2- Protection: Short circuit at the output, overload, battery voltage too high, battery voltage too low, temperature too high, 230 V AC at the inverter output, too high humming tension at the input-Features: operating temperature: -20 to +50 ° C (fan cooling), type of protection: IP21- Battery Connection: Battery cable of 1.5 meters supplied-230V AC connection: G-St18i connector- Weight (kg): 10- Dimensions (HXBXT in mm): 375x214x110- *Top factor with non -linear load 3: 1

The Phoenix Compact Inverter series has been developed for commercial use; it is suitable for a variety of applications. The development but without compromise on an inverter with clean sine wave output with high efficiency.A key feature is very high start performance. Phoenix inverters are capable of the high starting currents, for example, of refrigeration compressors, electric motors and similar appliances.Virtually unlimited power thanks to parallel and three-phase operation. Up to six inverter units can be connected in parallel for increased performance. Six 24/5000 units, for example, Make 24kW / 30kVA power. A three-phase operation is also possible.Computer Interfaces: All models have a RS-485 connection. All you need is our MK2 interface (see under accessories). This interface takes care of galvanic isolation between the inverter and the computer, and converts from RS-485 to RS-232. An RS-232 to USB conversion cable is also available. With the VEConfigure software that is downloaded for free, the inverters can be adjusted according to requirements. This includes output voltage and frequency, the upper and lower voltage limits and the programming of the relay. The relay can, for example, for generating signals in special situations or can be also used to start a generator.- Phoenix Inverter Type: C12 / 1200- Parallel and 3-phase operation: Yes- Input voltage (VDC): 9.5 to 17 V- Output: Output: 230 V ± 2%, frequency: 50 Hz ± 0.1% (may also be set to 60 Hz, and 240 V)- output power at 25 ° C (VA) *: 1200- Ausgangsdauerleistungbei25 ° C (W): 1000- Ausgangsdauerleistungbei40 ° C (W): 900- Peak Power (W): 2400- Max efficiency (%): 92nd- zero load (W): 8- no-load in AES mode (W): 5- no-load in Search mode (W): 2- protection: output short circuit, overload, battery voltage too high, battery voltage too low, temperature too high, 230 V AC at the inverter output, too high input voltage ripple- Description: Operating Temperature: -20 to +50 ° C (cooling fan) Protection: IP21- Battery connection: battery cable included 1.5 meters- 230V AC connection: G-ST18i connector- Weight (kg): 10- Dimensions (HxWxD in mm): 375x214x110- * Crest factor with non-linear load 3: 1