Für die sichere Fahrt haben wir Positionslaternen, sowohl mit herkömmlichen Glühlampen als auch mit LED-Leuchten inkl. BSH-Zulassung.
Für eine wahlweise helle und/oder gemütliche Beleuchtung unter Deck gibt es 12-Volt Lampen verschiedenster Art für die Innenbeleuchtung. Aber auch für die Beleuchtung an Deck und sogar unter Wasser ist mit unseren Außenleuchten gesorgt.
MARINE LED range- Very low power consumption- Pleasant warm white light color- The light color corresponds to conventional incandescent lamps- Large input voltage range, suitable for 12 and 24 V systems- Insensitive against voltage spikes (by dynamo, charger, etc.)- "burn out" prevents Integrated voltage regulation and guarantees long service life- The lamps with integrated power control function independently of the polarity- In connection with an electronic dimmer (pulse width modulation), the LED can be dimmed- Due to continuous development we reserve the right without notice in design and specifications to supply different items successor.- Energy efficiency class A +15 SMD LED.The design corresponds to a conventional light bulb, the filament was replaced by a SMD LED insert!Bayonet base with two Fußkontakten (BA15d) - (Picture 2 in the middle)Series: 15er SMD Globe with bayonet baseLuminous flux output typ .: 140 lumensColor temperature: warm white (2700 Kelvin)CRI:> 80Rated / rated life: up to 50,000 hLumen maintenance: 0.7Angle: 300 °Socket type (standard designation) BA15dConsumption: 1.6 wattsInput voltage: 10 - 30 V DC / 10 - 18 V AC at 50/60 Hz effectivelyReplaces: about 15-20W bayonet lamp *Dimmable: YesDimensions: Ø 25mm x 48mmWeight: 12 gWeight in blister: 23 gSwitching cycles:> 25,000Color Consistency: SDCM <7 (Standard Deviation of Color Matching)Energy efficiency class: A +Delay: none (<1 sec.)Power Factor: 0.8This article is to be used only for the marine sector.The usual use of these BA15D than single filament with floating base (e.g. anchor light on boats or in the vehicle interior). The BA15D can not be used as a replacement for a two-filament lamp (brake and tail light)The use as light source in motor vehicles is not permitted and prohibited. * 15 W as shown in Table 6 of the EU Regulation 244/2009Consumption in W was for decades as a benchmark for lamps alternatives.However, the prescribed formulas for determining equivalence do not necessarily reflect the realistic replacement again.The subjective perception of brightness of an LED lamp is highly dependent on the positioning and type of light.Most LED lamps emit light mainly in one direction. As a result, lamps are felt with a low equivalent value, according to the EU regulations as significantly brighter.
Adapter version G4-GY6.35 on base BA15D for LED lampsThis adapter has two contacts for the power supply below, the pins on the side are both at the same height.These adapters enable the use of LED or halogen lamps with G4/GU4 base in all lights with a 15 mm bayonet frame.Depending on the requirement, you can also use cylindrical lamps with a large beam angle or spots in your existing lights.Color: white/silverVersal type (standard designation): G4/ GU5.3/ GY6.35Base type (standard designation): BA15D (in Figure 3 in the middle)Dimensions: Ø 17 mm x 29 mmWeight Bulk: 8 gArea of application: 10 - 30 V Niedervolt, LED lampsScope of delivery: 1 adapterThis article can only be used for the naval area.The usual use of this BA15D is a single -down lamp with potential -free base (e.g. anchor light in boats or in the vehicle interior). The BA15D cannot be used as a replacement for a doubt lamp (brake and bottom).Use as a lamp in motor vehicles is not permitted and permissible.
Dimensions (Durchm.xL): 20 x 85 mmItem No .: 6772 A12 V, 25 W, BA15d (picture 2 left side)This article is to be used only for the marine sector.The use as light source in motor vehicles is not permitted and prohibited.
Suitable for all lights with Bajonett version BA15D (Fig. 2 in the middle)Brings double light intensity compared to conventional incandescent lamps in half power consumption!Art.-no.: 6860312 V, 5 W, BA15D, double contactThis article can only be used for the naval area.Use as a lamp in motor vehicles is not permitted and permissible.
Adapter holder G4-gy6.35 on E14 for LED lamps. Caution only use Niederspannug 10-30V!These adapters allow the use of LED or halogen Leuchitteln with G4 / GU4 base in all lights with 14mm screw mount.You can thus, depending on requirements and cylindrical Leuchittel with wide viewing angle or spots in your existing luminaires use.Color: white / silverSocket (standard designation): G4 / GU5.3 / GY6.35Socket type (standard designation) E14Weight bulk: 5 gScope: 10 - 30 V low-voltage, LED lampsWe expressly point out that navigation lights lose the authorization for use of this base with corresponding Leuchitteln. The base may therefore only for decorative purposes and are not used for operation on maritime and inland waterways!
Marine LED range- Very low energy requirement- The light color corresponds to conventional incandescent lamps- Large input voltage area, suitable for 12 and 24 V on -board nets- insensitive to tension tips (through Lima, charger, etc.)- Integrated voltage control prevents “burning down” and guarantees long service life- The lamps with integrated voltage control work regardless of the polarity- In conjunction with an electronic dimmer (pulse width modulation), the LEDs are dimmable- Due to constant technical development, we reserve the right to deliver deviating successor items without prior notice in design and technical data.- for position lanterns, no BSH approval, only exportSeries 1 lamp with 15 SMD globe with bayonet baseLight current tax type 140 lumensColor temperature 2700 Kelvin)CRI> 80Rated /nominal life of up to 50,000 hLight current maintenance 0.7Ray angle 300 °Base type (standard designation) Bay15D (Fig. 2 Left)Consumption 1.6 wattsInput voltage 10-30V DC / 10-18V AC at 50/60 Hz EffectiveReplaced approx. 20W bayonet lamp*Dimmable yesDimensions Ø 25 mm x 48 mmWeight 11 gWeight in the blister 22 gSchlag cycles> 25,000Color consistency sdcm <4Energy efficiency class [A-G]: GEPREL registration number 2019/2015: 773179Delay of switching no (<0.5 seconds)Power factor 0.8*15 W in accordance with Table 6 of the EU Regulation 244/2009The consumption in Walt was considered a comparative value for lamp alternatives for decades. However, the given formulas for equivalent determination do not necessarily reflect the realistic replacement. The subjective perception of the brightness of an LED lamp depends heavily on the positioning and type of light. Most LED lamps mainly emit the light in one direction. As a result, lamps with a low equivalence value are perceived as much brighter according to the EU regulations.IMPORTANT NOTE:Please note that the item offered for use on motor vehicles is not permitted and is not suitable!In contrast to the 2 threads used for brake light and the bottom light, the Bay15d base is deviated differently! + and - VE are on the two foot contacts with the lamp offered. The outer ring of the base is not occupied.
€10.20*
€11.30*(9.73% saved vs. recommended price)
MARINE LED- Very low power consumption- Pleasant warm white light color- The light color corresponds to conventional incandescent lamps- Large input voltage range, suitable for 12 and 24 V systems- Insensitive against voltage spikes (by dynamo, charger, etc.)- prevents Integrated Voltage Regulation '' burn '' and guarantees long service life- The Leuchittel with integrated power control function independently of the polarity- In connection with an electronic dimmer (pulse width modulation), the LED can be dimmed- Due to continuous development we reserve the right without notice in design and specifications to supply different items successor.1 illuminant with 24 SMD-LED MR 16 with frosted lens.In the on and off state is practically not noticeable that there is an LED light source.Suitable as replacement for halogen cold light reflector lamps (depth note).Series: 24er SMD pin baseLuminous flux output typ .: 130 lumensLamp Current 90 °: 125 LumenColor temperature: warm white (3000 Kelvin)CRI:> 65 *Life: up to 50,000 hRated / rated life: 0.7Angle: 80 °Base Type: GX5.3Consumption: 2.2 wattsInput voltage: 12 V DC at 50/60 Hz effectivelySubstitutes: 20 W halogen spot **Dimmable: YesDimensions: Ø 50 mm x 58 mmWeight: 44 gWeight in the Blister: 56 gSwitching cycles:> 25,000Color Consistency: SDCM <7 (Standard Deviation of Color Matching)Candela: 140Energy efficiency class: A +Delay: none (<1 sec.)Power Factor: 0.8* Putting of the goods took place prior to 08/2013. The color reproduction is not the current EU regulation 1194/2012.** 15 W as shown in Table 6 of the EU Regulation 1194/2012Consumption in W was for decades as a benchmark for lamps alternatives.However, the prescribed formulas for determining equivalence do not necessarily reflect the realistic replacement again.The subjective perception of brightness of an LED lamp is highly dependent on the positioning and type of light.Most LED lamps emit light mainly in one direction.As a result, lamps are felt with a low equivalent value, according to the EU regulations as significantly brighter.
€6.90*
€12.90*(46.51% saved vs. recommended price)
Total length approx. 48 mm, BA15D base (Fig. 2 in the middle)Art.-no.: 674312 V, 10 W, BA15D 6806 24 V, 10 W, BA15DThis article can only be used for the naval area.Use as a lamp in motor vehicles is not permitted and permissible.
MARINE LED- Very low power consumption- Pleasant warm white light color- The light color corresponds to conventional incandescent lamps- Large input voltage range, suitable for 12 and 24 V systems- Insensitive against voltage spikes (by dynamo, charger, etc.)- prevents Integrated Voltage Regulation '' burn '' and guarantees long service life- The Leuchittel with integrated power control function independently of the polarity- In connection with an electronic dimmer (pulse width modulation), the LED can be dimmed- Due to continuous development we reserve the right without notice in design and specifications to supply different items successor. 1 illuminant with 15 SMD LED.Suitable for all applications where a large angle is needed.suitable for combination with the bayonet socket adapters L18XX for many applications on board.Series: 15er SMD SpotLuminous flux output typ .: 90 lumensColor temperature: warm white (3000 Kelvin)CRI:> 80Rated / rated life: up to 50,000 hLumen maintenance: 0.7Angle: 300 °Socket type (standard designation): G4Consumption: 0.8 wattsInput voltage: 10 - 30 V DC / 10 - 18 V AC at 50/60 Hz effectivelySubstitutes: 15 W halogen spotlightDimmable: YesDimensions: Ø 13 mm x 34.7 mmWeight: 4 gWeight in the Blister: 14 gSwitching cycles:> 25,000Color Consistency: SDCM <4 (Standard Deviation of Color Matching)Energy efficiency class: A +Delay: none (<1 sec.)Power Factor: 0.8* 11 W as shown in Table 6 of the EU Regulation 244/2009Consumption in W was for decades as a benchmark for lamps alternatives.However, the prescribed formulas for determining equivalence do not necessarily reflect the realistic replacement again.The subjective perception of brightness of an LED lamp is highly dependent on the positioning and type of light.Most LED lamps emit light mainly in one direction.As a result, lamps are felt with a low equivalent value, according to the EU regulations as significantly brighter.
Marine LED- Very low energy requirement- Pleasant warm and white light color- The light color corresponds to conventional incandescent lamps- Large input voltage area, suitable for 12 and 24 V on -board nets- insensitive to tension tips (through Lima, charger, etc.)- Integrated voltage control '' burns' 'burn' and guarantees long service life- The lamps with integrated voltage control work regardless of the polarity- In conjunction with an electronic dimmer (pulse width modulation), the LEDs are dimmable- Due to constant technical development, we reserve the right to deliver deviating successor items without prior notice in design and technical data.1 illuminant with 15 SMD LED, with a stray disc.Series: 15 SMD pen baseLight current tax type.: 240 lumensDimination light flow 90 °: 125 lumensColor temperature: warm white (approx. 3000 Kelvin)Cri:> 80Lifespan: up to 50,000 hRated /nominal life: 0.7Ray angle: 125 °Base type: GU5.3Consumption: 2.6 wattsInput voltage: 10 - 30 V DC / 10 - 18 V AC at 50/60 Hz EffectiveReplaced: approx. 35 w halogen spot*Dimmable: yesDimensions: Ø 50 mm x 45 mmWeight: 32 gWeight in the blister: 44 gSchlag cycles:> 25,000Color consistency: SDCM <7 (Standard Deviation of Color Matching)Candela: 140Energy efficiency class [A-G]: FEprel registration number 2019/2015: 773148Delay of switching: no (<1 sec.)Power factor: 0.8*24 W in accordance with Table 6 of the EU Regulation 244/2009The consumption in Walt was considered a comparative value for lamp alternatives for decades.However, the given formulas for equivalent determination do not necessarily reflect the realistic replacement.The subjective perception of the brightness of an LED lamp depends heavily on the positioning and type of light.Most LED lamps mainly emit the light in one direction.As a result, lamps with a low equivalence value are perceived as much brighter according to the EU regulations.
€10.90*
€12.30*(11.38% saved vs. recommended price)
Marine LED range- Very low energy requirement- Pleasant warm and white light color- The light color corresponds to conventional incandescent lamps- Large input voltage area, suitable for 12 and 24 V on -board nets- insensitive to tension tips (through Lima, charger, etc.)- Integrated voltage control prevents “burning down” and guarantees long service life- The lamps with integrated voltage control work regardless of the polarity- In conjunction with an electronic dimmer (pulse width modulation), the LEDs are dimmable- Due to constant technical development, we reserve the right to deliver deviating successor items without prior notice in design and technical data.1 lamp with 6 SMD LED, radiating forward.Bajonet base with two foot contacts (BA15D),Series: 6 SMD spot with bayonet baseLight current tax type.: 100 lumensColor temperature: warm white (approx. 3000 Kelvin)Cri:> 80Rated /nominal life duration: up to 35,000 hLight stream maintenance: 0.7Ray angle: 125 °Base type: BA15D (Fig. 2 in the middle)Consumption: 1 wattsInput voltage: 10 - 30 V DC / 10 - 18 V AC at 50/60 Hz EffectiveReplaced: approx. 15-20 w halogen spot*Dimmable: yesDimensions: Ø 26.7 mm x 38 mmWeight: 9 gWeight in the blister: 20 gSchlag cycles:> 25,000Color consistency: SDCM <7 (Standard Deviation of Color Matching)Energy efficiency class [A-G]: FEprel registration number 2019/2015: 767011Delay of switching: no (<1Sec.)Power factor: 0.8This article can only be used for the naval area.The usual use of this BA15D is a single -down lamp with potential -free base (e.g. anchor light in boats or in the vehicle interior). The BA15D cannot be used as a replacement for a doubt lamp (brake and bottom).Use as a lamp in motor vehicles is not permitted and permissible.*15 W in accordance with Table 6 of the EU Regulation 244/2009The consumption in Walt was considered a comparative value for lamp alternatives for decades.However, the given formulas for equivalent determination do not necessarily reflect the realistic replacement.The subjective perception of the brightness of an LED lamp depends heavily on the positioning and type of light.Most LED lamps mainly emit the light in one direction. As a result, lamps with a low equivalence value are perceived as much brighter according to the EU regulations.