Tankanzeigen von Philippi und Blue Sea

Float switch for lateral mounting in tanks for level detection.opens or closes depending on the installation position of the switches with rising or falling level.The float switch can be mounted externally on the tank without having to put a lock nut from the inside.By a sealing ring is tightened from the outside, the installation is very easy retrospectively from outside.· Mounting hole: ø 22 to 24 mm.· Seal 12 mm wide for wall thickness up to max. 5 mm, suitable only for low inflation pressure.· Switching current max. 0.5 A.

Ultrasonic level sensors with voltage output 0,5-2,5V, Type 20 UTV

The accurate and reliable level measurement by means of pressure probeThe pressure probe TDS is suspended as an immersion probe to the bottom of a tank.About the hydrostatic pressure of the liquid, the probe measures the current level of the liquid.The PUR connection cable of the submersible probe contains a thin air tube to the back pressure to compensate for the measuring cell.This will automatically compensate for variations in air pressure and do not result in erroneous measurements.Suitable for diesel, water, sewage and holding tanks, not for gasoline, kerosene, petroleum (Ex-zone).Very accurate and reliable measurement with high measurement resolution (about 1 cm), even with gush.The package includes a mounting flange (Ø 79 mm) with different hole circles (analog TGT and SAE) and gland and indication of the depth of the tank containing a guide tube for mechanical guidance of the encoder.The pressure probe is inserted 2 TDS (System monitor PSM) in communication with a tank monitor TCM 4V or tank interface CMT.Caution: When TCM4V a hardware adjustment "4-20 mA" is necessary!· Measuring range 0 - 200 mbar (corresponding to 1-200 cm)· Output DC 4 - 20 mA, 2-wire principle· Operating voltage 10 - 30 V DC via measuring line and series resistor· Operating temperature range +5 - 40 ° C· Probe Housing stainless steel 1.4404 (316 L, V4A), L 97 mm, Ø 22 mm· Weight approximately 0.2 kg without cable· Submersible cable PUr black, m length 6, oil resistant

Analog fuel indicator in high quality execution. Stainless steel housing, windscreen made of 4 mm thick glass. The instruments are waterproof from the front and are therefore very suitable for external use.- Dials illuminated- Fastening by assembly bracket on the back- Installation diameter: through the. 52 mm hole- Operating voltage: 12 V (24 V with resistance possible)- Resistance area 10 - 180 OhmSuitable for Philippi tanker TGT.Turotest fuel gauge fuel,Through the. 52 mm

- for fuel depth 800 mm- Non -contact level measurement of tanks using ultrasound technology- no moving parts in the tank that can be dirty or damaged- Practically maintenance -free, ideal for fecal tanks- Simple exchange of existing, conventional tankers- Suitable for diesel, water and fecal tanks, not suitable for petrol- Output signal UTV: voltage range 0.5 - 2.5 V, can be used for TCM tank monitor and UTV52 round instruments- Fastening according to SAE standard (5 fastening holes in the hole circuit of 53 mm)- Structure height 25 mm, diameter of the donor Ø 68 mm, bore at least 36 mm- Suitable for 12 and 24 V on -board voltage- The first 5 cm of the measuring range cannot be measured and are fully interpreted as a tank

- mm for tank depth 700- Non-contact level measurement of tanks using ultrasonic technology- No moving parts in the tank, which may be dirty or damaged- Virtually maintenance free, ideal for holding tanks- Easy replacement of existing, conventional tank sensor- Suitable for diesel, water and holding tanks, not suitable for gasoline- output UTV: voltage range 0.5 - 2.5 V, suitable for TCM tank monitor and UTV52 round instruments- output UTN: resistance range of 10 - 180 °, for operation with VDO and Volvo Penta round instruments- Mounting according to SAE standard (5 mm fixing holes in the hole circle of 53)- installation height 25 mm, diameter of the encoder Ø 68 mm, 36 mm bore at least- Suitable for 12 and 24 V on-board voltage- The first 5 cm of the measuring range can not be measured and be fully interpreted as a tank

- mm for tank depth 600- Non-contact level measurement of tanks using ultrasonic technology- No moving parts in the tank, which may be dirty or damaged- Virtually maintenance free, ideal for holding tanks- Easy replacement of existing, conventional tank sensor- Suitable for diesel, water and holding tanks, not suitable for gasoline- output UTV: voltage range 0.5 - 2.5 V, suitable for TCM tank monitor and UTV52 round instruments- output UTN: resistance range of 10 - 180 °, for operation with VDO and Volvo Penta round instruments- Mounting according to SAE standard (5 mm fixing holes in the hole circle of 53)- installation height 25 mm, diameter of the encoder Ø 68 mm, 36 mm bore at least- Suitable for 12 and 24 V on-board voltage- The first 5 cm of the measuring range can not be measured and be fully interpreted as a tank

- mm for tank depth 500- Non-contact level measurement of tanks using ultrasonic technology- No moving parts in the tank, which may be dirty or damaged- Virtually maintenance free, ideal for holding tanks- Easy replacement of existing, conventional tank sensor- Suitable for diesel, water and holding tanks, not suitable for gasoline- output UTV: voltage range 0.5 - 2.5 V, suitable for TCM tank monitor and UTV52 round instruments- output UTN: resistance range of 10 - 180 °, for operation with VDO and Volvo Penta round instruments- Mounting according to SAE standard (5 mm fixing holes in the hole circle of 53)- installation height 25 mm, diameter of the encoder Ø 68 mm, 36 mm bore at least- Suitable for 12 and 24 V on-board voltage- The first 5 cm of the measuring range can not be measured and be fully interpreted as a tank

- for fuel depth 450 mm- Non -contact level measurement of tanks using ultrasound technology- no moving parts in the tank that can be dirty or damaged- Practically maintenance -free, ideal for fecal tanks- Simple exchange of existing, conventional tankers- Suitable for diesel, water and fecal tanks, not suitable for petrol- Output signal UTV: voltage range 0.5 - 2.5 V, can be used for TCM tank monitor and UTV52 round instruments- Fastening according to SAE standard (5 fastening holes in the hole circuit of 53 mm)- Structure height 25 mm, diameter of the donor Ø 68 mm, bore at least 36 mm- Suitable for 12 and 24 V on -board voltage- The first 5 cm of the measuring range cannot be measured and are fully interpreted as a tank

- mm for tank depth 400- Non-contact level measurement of tanks using ultrasonic technology- No moving parts in the tank, which may be dirty or damaged- Virtually maintenance free, ideal for holding tanks- Easy replacement of existing, conventional tank sensor- Suitable for diesel, water and holding tanks, not suitable for gasoline- output UTV: voltage range 0.5 - 2.5 V, suitable for TCM tank monitor and UTV52 round instruments- output UTN: resistance range of 10 - 180 °, for operation with VDO and Volvo Penta round instruments- Mounting according to SAE standard (5 mm fixing holes in the hole circle of 53)- installation height 25 mm, diameter of the encoder Ø 68 mm, 36 mm bore at least- Suitable for 12 and 24 V on-board voltage- The first 5 cm of the measuring range can not be measured and be fully interpreted as a tank

- for fuel depth 350 mm- Non -contact level measurement of tanks using ultrasound technology- no moving parts in the tank that can be dirty or damaged- Practically maintenance -free, ideal for fecal tanks- Simple exchange of existing, conventional tankers- Suitable for diesel, water and fecal tanks, not suitable for petrol- Output signal UTV: voltage range 0.5 - 2.5 V, can be used for TCM tank monitor and UTV52 round instruments- Fastening according to SAE standard (5 fastening holes in the hole circuit of 53 mm)- Structure height 25 mm, diameter of the donor Ø 68 mm, bore at least 36 mm- Suitable for 12 and 24 V on -board voltage- The first 5 cm of the measuring range cannot be measured and are fully interpreted as a tank

- mm for tank depth 300- Non-contact level measurement of tanks using ultrasonic technology- No moving parts in the tank, which may be dirty or damaged- Virtually maintenance free, ideal for holding tanks- Easy replacement of existing, conventional tank sensor- Suitable for diesel, water and holding tanks, not suitable for gasoline- output UTV: voltage range 0.5 - 2.5 V, suitable for TCM tank monitor and UTV52 round instruments- output UTN: resistance range of 10 - 180 °, for operation with VDO and Volvo Penta round instruments- Mounting according to SAE standard (5 mm fixing holes in the hole circle of 53)- installation height 25 mm, diameter of the encoder Ø 68 mm, 36 mm bore at least- Suitable for 12 and 24 V on-board voltage- The first 5 cm of the measuring range can not be measured and be fully interpreted as a tank

- for fuel depth 250 mm- Non -contact level measurement of tanks using ultrasound technology- no moving parts in the tank that can be dirty or damaged- Practically maintenance -free, ideal for fecal tanks- Simple exchange of existing, conventional tankers- Suitable for diesel, water and fecal tanks, not suitable for petrol- Output signal UTV: voltage range 0.5 - 2.5 V, can be used for TCM tank monitor and UTV52 round instruments- Fastening according to SAE standard (5 fastening holes in the hole circuit of 53 mm)- Structure height 25 mm, diameter of the donor Ø 68 mm, bore at least 36 mm- Suitable for 12 and 24 V on -board voltage- The first 5 cm of the measuring range cannot be measured and are fully interpreted as a tank

Club plug for thread fanschType TRV

Type TGW 450, diving pipe provider A2including thread fans and poetry

TGT 450, dip tube encoder incl.Threaded and sealing

Faecal tank switch with a thread fleet GWF 080 and rubber sealType TRS 130