Sammelschienen (Busbars) als Verteiler für die Bordelektrik

PHILIPPI - Power Install System 250MINUS-Sammelschiene 6-fach. Strombelastbarkeit 250 A. Alle Bolzen M10, Abmessungen  L 212x B 40 x H 50 mm Die Installation von Hochstromkomponenten wie Hauptschalter und Sicherungen ist eine platz- und zeitraubende Aufgabe, da die Verbindung der einzelnen Komponenten aufgrund von mechanischen Unterschieden oftmals nur mit flexiblen Leitungen hergestellt werden kann. Unser neu entwickeltes Hauptverteilungssystem spart enorm viel Platz, Zeit und Geld. Zudem erhöht es die Sicherheit, da alle Verbindungen über passende Kupferlaschen miteinander verbunden werden. Die zentrale Komponenten sind der mechanisch schaltbare (EBH 250) oder der elektrisch fernbedienbare Batterie-Hauptschalter (FBR/TSA/FBC 265). Die nachfolgende Absicherung kann mit den Streifensicherungshalter ESH oder den Bolzensicherunghaltern EBF erfolgen.Am Ein- und Ausgang der Batterie-Hauptschalter kann ein Sicherungs-block ESF montiert werden, um Messleitungen und Verbraucher wie Bilgenpumpe, Ladegerät oder Heizung mit Dauerplus zu versorgen. Die Strombelastbarkeit des Systems beträgt 250 A und ist für DC 12 V und 24 V geeignet.Durch Kombination von mehreren Komponenten lässt sich eine kompakte Hauptstromverteilung für Starter- und Verbraucher-Batterie aufbauen, die zusätzlich mit einem Notschalter zum Start des Motors über die Verbraucher-Batterie ergänzt werden kann. Alternativ kann auch ein Laderelais eingesetzt werden. Dabei können mechanische oder fernbedienbare Hauptschalter (FBA / TSA / FBC) verwendet werden. An die Hauptschalterausgänge können Sicherungsblöcke angebaut werden, um die Hauptleitungen abzusichern. Seitlich können noch Kleinsicherungs-blöcke zur Absicherung von Dauerplus-Verbrauchern ergänzt werden. Die Verbindung erfolgt mit den passenden Verbindungslaschen.

PHILIPPI - Power Install System 250MINUS-Sammelschiene 3-fach. Strombelastbarkeit 250 A. Alle Bolzen M10, Abmessungen  L 119 x B 40 x H 50 mm Die Installation von Hochstromkomponenten wie Hauptschalter und Sicherungen ist eine platz- und zeitraubende Aufgabe, da die Verbindung der einzelnen Komponenten aufgrund von mechanischen Unterschieden oftmals nur mit flexiblen Leitungen hergestellt werden kann. Unser neu entwickeltes Hauptverteilungssystem spart enorm viel Platz, Zeit und Geld. Zudem erhöht es die Sicherheit, da alle Verbindungen über passende Kupferlaschen miteinander verbunden werden. Die zentrale Komponenten sind der mechanisch schaltbare (EBH 250) oder der elektrisch fernbedienbare Batterie-Hauptschalter (FBR/TSA/FBC 265). Die nachfolgende Absicherung kann mit den Streifensicherungshalter ESH oder den Bolzensicherunghaltern EBF erfolgen.Am Ein- und Ausgang der Batterie-Hauptschalter kann ein Sicherungs-block ESF montiert werden, um Messleitungen und Verbraucher wie Bilgenpumpe, Ladegerät oder Heizung mit Dauerplus zu versorgen. Die Strombelastbarkeit des Systems beträgt 250 A und ist für DC 12 V und 24 V geeignet.Durch Kombination von mehreren Komponenten lässt sich eine kompakte Hauptstromverteilung für Starter- und Verbraucher-Batterie aufbauen, die zusätzlich mit einem Notschalter zum Start des Motors über die Verbraucher-Batterie ergänzt werden kann. Alternativ kann auch ein Laderelais eingesetzt werden. Dabei können mechanische oder fernbedienbare Hauptschalter (FBA / TSA / FBC) verwendet werden. An die Hauptschalterausgänge können Sicherungsblöcke angebaut werden, um die Hauptleitungen abzusichern. Seitlich können noch Kleinsicherungs-blöcke zur Absicherung von Dauerplus-Verbrauchern ergänzt werden. Die Verbindung erfolgt mit den passenden Verbindungslaschen.

Philippi - Power Install System 250Binding rails copper nickel -plated 80 mm² for the connection of the PowerInnstall elements.EBV 2-2: Punch 55 mm + 40 mmThe installation of high-current components such as the main switch and fuses is a space and time-consuming task, since the connection of the individual components due to mechanical differences can often only be established with flexible lines. Our newly developed main distribution system saves a lot of space, time and money. It also increases security because all connections are connected to each other via suitable copper taps. The central components are the mechanically switchable (EBH 250) or the electrically remote-controllable battery switch (FBR/TSA/FBC 265). The subsequent protection can take place with the strip protection holder ESH or the EBF bolt fuse holders.At the input and output of the battery switch switches, a safety block ESF can be installed to supply measuring lines and consumers such as bilge pump, charger or heating with a permanent plus. The current resilience of the system is 250 A and is suitable for DC 12 V and 24 V.By combining several components, a compact main power distribution for starter and consumer battery can be set up, which can also be supplemented with an emergency switch at the start of the engine via the consumer battery. Alternatively, a loading relay can also be used. Mechanical or remote control main switch (FBA / TSA / FBC) can be used. Security blocks can be attached to the main switch outputs to secure the main lines. Small safety blocks to secure permanent plus consumers can also be supplemented on the side. The connection is made with the appropriate connecting taps.

Philippi - Power Install System 250Binding rails copper nickel -plated 80 mm² for the connection of the PowerInnstall elements.EBV 2-1: Location 55 mmThe installation of high-current components such as the main switch and fuses is a space and time-consuming task, since the connection of the individual components due to mechanical differences can often only be established with flexible lines. Our newly developed main distribution system saves a lot of space, time and money. It also increases security because all connections are connected to each other via suitable copper taps. The central components are the mechanically switchable (EBH 250) or the electrically remote-controllable battery switch (FBR/TSA/FBC 265). The subsequent protection can take place with the strip protection holder ESH or the EBF bolt fuse holders.At the input and output of the battery switch switches, a safety block ESF can be installed to supply measuring lines and consumers such as bilge pump, charger or heating with a permanent plus. The current resilience of the system is 250 A and is suitable for DC 12 V and 24 V.By combining several components, a compact main power distribution for starter and consumer battery can be set up, which can also be supplemented with an emergency switch at the start of the engine via the consumer battery. Alternatively, a loading relay can also be used. Mechanical or remote control main switch (FBA / TSA / FBC) can be used. Security blocks can be attached to the main switch outputs to secure the main lines. Small safety blocks to secure permanent plus consumers can also be supplemented on the side. The connection is made with the appropriate connecting taps.

Philippi - Power Install System 250Binding rails copper nickel -plated 80 mm² for the connection of the PowerInnstall elements.EBV 1: Punch 25-33 mmThe installation of high-current components such as the main switch and fuses is a space and time-consuming task, since the connection of the individual components due to mechanical differences can often only be established with flexible lines. Our newly developed main distribution system saves a lot of space, time and money. It also increases security because all connections are connected to each other via suitable copper taps. The central components are the mechanically switchable (EBH 250) or the electrically remote-controllable battery switch (FBR/TSA/FBC 265). The subsequent protection can take place with the strip protection holder ESH or the EBF bolt fuse holders.At the input and output of the battery switch switches, a safety block ESF can be installed to supply measuring lines and consumers such as bilge pump, charger or heating with a permanent plus. The current resilience of the system is 250 A and is suitable for DC 12 V and 24 V.By combining several components, a compact main power distribution for starter and consumer battery can be set up, which can also be supplemented with an emergency switch at the start of the engine via the consumer battery. Alternatively, a loading relay can also be used. Mechanical or remote control main switch (FBA / TSA / FBC) can be used. Security blocks can be attached to the main switch outputs to secure the main lines. Small safety blocks to secure permanent plus consumers can also be supplemented on the side. The connection is made with the appropriate connecting taps.

Mass busbar Type MSB 3

fits for 2127/2128 and BS2127/BS2128

2 threaded bolt Ø 5/16 "(7.9 mm)6 other fastening options

Assembly steam M10Thread length 25 mmDimensions L 32 x W 28 x H 45 mm

Delivery takes place without a collective base!

Composite cover as protection against contact for busbar PowerBar 1000 with 12 threaded bolts.Fits BS1991 / Art. 1,950,202 and BS1993 / Art. 1950204

Composite cover as protection against contact for busbar PowerBar 1000 with 8 threaded bolts.Fits BS1990 / Art. 1,950,201 and BS1992 / Art. 1950203

High load collective rail with12 threaded bolt Ø 5/16 ”(7.9 mm),5 screw connections Ø 5 mm and11 screw connections Ø 4 mm.Complex electrical systems require a central point at which all large and small ladder can be connected. The Powerbar 1000 high -speed collection rail offers different sizes and screw connections for contact with a maximum load capacity of 1,000 amps.- consisting of solid copper with tinned surface- In the height, arranged contacts- Collection rail can be shortened if necessary- Included plastic coverage in the scope of delivery- Tension range max. 150 V- permanent load max. 1,000 a- Dimensions (WXHXT, including optionally mantilable cover): 364 x 68 x 116 mm.

High load collective rail with8 threaded bolt Ø 5/16 ”(7.9 mm),5 screw connections Ø 5 mm and11 screw connections Ø 4 mm.Complex electrical systems require a central point where all large and small ladder can be connected. The Hochlast collection rail Powerbar 1000 offers different sizes and screw connections for contact with a maximum load capacity of 1,000 amps.- consisting of solid copper with tinned surface- In the height, arranged contacts- Collection rail can be shortened if necessary- Plastic coverage is included- Tension range max. 150 V- permanent load max. 1,000 a- Dimensions (WXHXT, including optionally assembled cover): 300 x 68 x 116 mm.

High load busbar 12 with threaded bolt diameter 3/8 "(9.5 mm), 5 mm screw diameter 5 mm and 11 screw O 4.Complex electrical systems require a central point on which all large and small conductors can be connected. The high load busbar PowerBar 1000 offers at a maximum load capacity of 1,000 Ampere differently sized threaded bolt and screw connections for the contacting.- Consists of solid copper with a tin coated finish- In the height offset arrangement of the contacts- busbar can be shortened if necessary- plastic cover available as an accessory- Voltage range max. 150 V- continuous load max. 1000 A- dimensions (. BxHxT, including optional cover): 364 x 68 x 116 mm.

High load busbar with 8 threaded bolts Ø 3/8 "(9.5 mm), 5 mm screw diameter 5 mm and 11 screw O 4.Complex electrical systems require a central point on which all large and small conductors can be connected. The high load busbar PowerBar 1000 offers at a maximum load capacity of 1,000 Ampere differently sized threaded bolt and screw connections for the contacting.- Consists of solid copper with a tin coated finish- In the height offset arrangement of the contacts- busbar can be shortened if necessary- plastic cover available as an accessory- Voltage range max. 150 V- continuous load max. 1000 A- dimensions (. BxHxT, including optional cover): 300 x 68 x 116 mm.

Busbar with brass contacts. 20 ports Ø 4 mm, 2 bolts Ø 6 mm.Dimensions (LxWxH): 226 x 32 x 27 mm