Blue Solar

Ultra -fast maximum power point tracking (mppt)Especially when the sky is covered, when the light intensity is constantly changing, an extremely fast MPPT controller improves the energy yield compared to PWM charging controls by up to 30 % and compared to slower mpp liders by up to 10 %.Load exitA too deep discharge of the battery can be prevented by connecting all loads to the load exit.The load exit separates the loads when the battery has been unloaded to a given voltage value.Alternatively, an algorithm for intelligent battery management can also be selected: see Battery Life.The load exit is short -circuit -proof.Some loads (especially inverters) can best be connected to the battery directly.The versiler remote control can best be connected to the load exit. Under certain circumstances, a special interface cable is required, please note the manual.Battery Life: Intelligent battery managementIf the solar charging controller is not able to charge the battery within one day to its full capacity, the status of the battery constantly changes between "partially charged" and "end of the discharge".This operating mode (no regular charging) damages a lead-acid battery within a few weeks or months.The Battery Life Algorithm monitors the charging status of the battery and, if necessary, it increases the threshold every day to separate the load (i.e., the load is separated earlier) until the energy obtained is sufficient to charge the battery up to almost 100 %.From this point, the threshold value for switching off the load is modulated, so that the charge is almost 100 % reached about once a week.Programmable battery charging algorithmFor more information, see the Software section on the Victron Energy website.Day/night taxation and light insulation optionFor more information, see the Software section on the Victron Energy website.Options for programming, data in real time and display of the course- Modern Apple and Android smartphones, tablets, MacBooks and other devices: Find screenshotsYou in the information sheets of Ve.direct Bluetooth Smart Dongles and the MPPT app.Battery voltage: 12/24V automatic choiceNominal power: 15aName PV performance, 12 V 1a, b): 220WName PV performance, 24 V 1a, b): 440WMax. PV short circuit current 2): 15aAutomatic load shutdown: Yes, maximum Last 15aMaximum PV empty voltage: 75VTop efficiency: 98%Self -consumption: 12V: 20 MA 24V: 10 MA"Constant" charging voltage (absorption): 14.4V / 28.8V (adjustable)"Conservation" charging voltage (float): 13.8V / 27.6V (regulable)Ladeal gorithm: multi -stage, adaptiveTemperature compensation: -16 mv/° C or -32 mv/° CInterruption -free / lace load current: 15a / 50aSwitching off the load with low voltage: 11.1V / 22.2V or 11.8V / 23.6V or Batterlife algorithmAnother connect the load according to low voltage: 13.1V / 26.2V or 14V / 28V or BatteryLife algorithmProtection: battery reversal (securing) Short circuit output / overheatingOperating temperature: -30 ° C to +60 ° C (full nominal output up to 40 ° C)Moisture: 95% not condensingData communication sport: ve.directConnections: 6 QMM / AWG10Protection class: IP43 (electronic components), IP22 (connection areaWeight: 0.5kgDimensions (HXBXT): 100 x 113 x 40mm1a) If more PV current is connected, the controller limits the input performance.1b) The PV voltage must reach at least the amount of VBAT + 5V so that the controller takes up the operation. Then the minimum value of the PV voltage is at VBAT + 1V.2) A PV system with a higher short-circuit current can damage the controller.

Ultra fast Maximum Power Point Tracking (MPPT)Especially in overcast sky, when the light intensity is constantly changing, an extremely fast MPPT controller improves the energy yield as compared to PWM charge controllers by up to 30% and in comparison to slower MPPTReglern by up to 10%.load outputA can be prevented by all loads are connected to the output load to deep discharge of the battery.The load output disconnects the loads when the battery has been up to a predetermined voltage value discharged.Alternatively, can also choose an algorithm for intelligent battery management: See Battery Life.The load output is short-circuit proof.Some loads (particularly inverter) can be connected directly to the battery at best.The inverter remote control is best to the load output connect. Under certain circumstances, a special interface cable is required, please refer to the manual.Battery Life: intelligent battery managementIf the solar charging controller is not able to charge the battery within one day up to its full capacity, the status of the battery changes constantly "partially loaded" and between "the end of discharge" back and forth.This mode of operation (no regular full charging) damaged a lead-acid battery within a few weeks or months.The Battery Life algorithm monitors the state of charge of the battery and, if necessary he lifts every day the threshold value for separating the load on (i. E., The load is disconnected earlier) until the recovered energy sufficient to charge the battery up to almost 100%.From this point, the threshold value is modulated for the disconnection of the load, so that the charging nearly 100% is achieved about once weekly.Programmable battery charging algorithmFor more information, see the section Software on the Victron Energy website.Day / night time control and light insulation optionFor more information, see the section Software on the Victron Energy website.Options for programming, real-time data and display the course- Modern Apple and Android smartphones, tablets, Macbooks and other devices: find screenshots for this purposeIn the info sheets of VE.Direct Bluetooth Smart dongle and the MPPT app.Battery voltage: 12 / 24V automatic selectionNominal charging current: 10ANominal PV power, 12 V 1a, b): 145WNominal PV power, 24 V 1a, b): 290WMax. PV short-circuit current 2): 10AAutomatic load disconnect Yes, maximum load 15AMaximum PV open voltage: 75VPeak efficiency: 98%Power consumption: 12V: 24V 20 mA: 10 mA"Constant" -Ladespannung (absorption): 14.4V / 28.8V (adjustable)"Conservation" -Ladespannung (float): 13.8V / 27.6V (adjustable)Charging algorithm: multi-level, adaptiveTemperature Compensation: -16 mV / ° C and -32 mV / ° CUninterrupted / peak load current: 15A / 50ASwitching off the load at a low voltage: 11.1V / 22,2V or 11.8V / or 23,6V Battery Life algorithmReconnecting the load to a low voltage: 13,1V / 26,2V or 14V / 28V or Battery Life algorithmProtection: Battery reverse polarity (fuse) Output short circuit / overheatingOperating Temperature: -30 ° C to + 60 ° C (full rated output up to 40 ° C)Humidity: 95% non-condensingData communication port: VE.DirectConnections: 6mm² / AWG10Protection: IP43 (electronic components), IP22 (connection regionWeight: 0.5kgDimensions (HxWxD): 100 x 113 x 40mm1a) If more PV power is connected, the controller limits the input power.1b) The PV voltage must at least the height of Vbat + reach 5V, so that the controller operation Tapes. After that, the minimum value of the PV voltage at Vbat + 1V.2) A PV system with a higher short-circuit current can damage the controller.

Dieser MPPT-Laderegler bietet eine effiziente Energieumwandlung für Solaranlagen mit einer maximalen Eingangsspannung von 150V und einem Strom von 45A. Er eignet sich ideal für kleinere bis mittlere Solarsysteme.Technische Daten:Spannung: 150VMaximalstrom: 45A.

Ultra -fast maximum power point tracking (mppt)Especially when the sky is covered, when the light intensity is constantly changing, an extremely fast MPPT controller improves the energy yield compared to PWM charging controls by up to 30% and compared to slower MPPT regulators by up to 10%.Advanced maximum Power Point detection in part shading.In the event of a partial shading, two or more points of maximum performance (MPP) may be available on the electricity voltage curve.Conventional MPTS tend to adjust to a local MPP.However, this may not be the optimal MPP.The innovative algorithm of the Bluesolar device will always maximize the energy yield by adjusting itself to the optimal MPP.Excellent efficiencyNo cooling fan. Maximum efficiency at over 98%. Full of output current up to 40 ° C (104 ° f).Flexible loading algorithmsFully programmable loading algorithm (also note the software page on the Victron Energy website) and eight pre-programmed algorithms that can be selected using a rotary knob (other details can be found in the manual).Comprehensive electronic protectionOverheating protection and load reduction at high temperatures.Protection against PV short circuit and PV solutions.PV backstream protection.Internal temperature sensorCompensates for constant and charging conservation voltages after temperature.Options for displaying data in real time- Apple and Android smartphones, tablets and other devices: Note the VE.Direct to Bluetooth Smart Dongle- Color Control panelBattery voltage: 12/24 V automatic choiceNominal power: 30aName PV performance, 12V 1A, b): 440WName PV performance, 24 V 1a, b): 880WMaximum PV empty voltage: 100VMax. PV short circuit current 2): 35aTop efficiency: 98%Self -consumption 12V: 30 MA 24V: 20 MA"Constant" charging voltage (absorption) Standard settings: 14.4 V / 28.8 V (adjustable)"Conservation" charging voltage (float) Standard settings: 13.8 V / 27.6 V (regulable)Ladeal gorithm: multi -stage, adaptiveTemperature compensation: -16 mv/° C or -32 mv/° CProtection: Polation on battery (backup, no access by the user), PV solutions, output short circuit, overheating, overheatingOperating temperature: -30 ° C to +60 ° C (full nominal output up to 40 ° C)Moisture: 95% not condensingData communication sport: ve.directConnections: 13 mm / AWG6Protection class: IP43 (electronic components), IP22 (connection area)Weight: 1.3 kgDimensions (HXBXT): 130 x 186 x 70 mm1a) If more PV current is connected, the controller limits the input performance.1b) The PV voltage must reach at least the amount of VBAT + 5 V so that the controller takes up the operation. Then the minimum value of the PV voltage is at VBAT + 1 V.2) A PV system with a higher short-circuit current can damage the controller.

Dieser MPPT-Laderegler eignet sich für Solarsysteme bis zu 48V. Er maximiert den Ertrag von Solaranlagen, indem er die maximale Leistung aus den Solarpanelen herausholt. Ideal für mittlere Systeme.Technische Daten:Spannung: bis 48VMaximalstrom: 20A.

Ultra -fast maximum power point tracking (mppt)Especially when the sky is covered, when the light intensity is constantly changing, an extremely fast MPPT controller improves the energy yield compared to PWM charging controls by up to 30% and compared to slower MPPT regulators by up to 10%.Advanced maximum Power Point detection in part shading.In the event of a partial shading, two or more points of maximum performance (MPP) may be available on the electricity voltage curve.Conventional MPTS tend to adjust to a local MPP.However, this may not be the optimal MPP.The innovative algorithm of the Bluesolar device will always maximize the energy yield by adjusting itself to the optimal MPP.Excellent efficiencyNo cooling fan. Maximum efficiency at over 98%. Full of output current up to 40 ° C (104 ° f).Flexible loading algorithmsFully programmable loading algorithm (also note the software page on the Victron Energy website) and eight pre-programmed algorithms that can be selected using a rotary knob (other details can be found in the manual).Comprehensive electronic protectionOverheating protection and load reduction at high temperatures.Protection against PV short circuit and PV solutions.PV backstream protection.Internal temperature sensorCompensates for constant and charging conservation voltages after temperature.Options for displaying data in real time- Apple and Android smartphones, tablets and other devices: Note the VE.Direct to Bluetooth Smart Dongle- Color Control panelBattery voltage: 12/24/48V Auto Select (software tool required to select 36V)Nominal power: 70aName PV performance, 12 V 1a, b): 1000WName PV performance, 24V 1A, b): 2000WName PV performance, 48V 1A, b): 4000WMax. Short -circuit current solar system 2): 50AMaximum PV empty voltage: 150 V Absolute maximum Coldest conditions, 145 V maximum value for switching and operationMax. Effect: 98%Self -consumption: 10mA"Constant" charging voltage (absorption) Standard settings: 14.4 / 28.8 / 43.2 / 57.6V (regulable)"Conservation" charging voltage (float) Standard settings: 13.8 / 27.6 / 41.4 / 55.2V (regulable)Ladeal gorithm: multi -stage, adaptiveTemperature compensation: -16mv / -32mv / -64mv / ° CProtection: Polation to battery (backup, no access by the user) / PV solutions / output cocoing / over temperatureOperating temperature: -30 ° C to +60 ° C (full nominal output up to 40 ° C)Moisture: 95% not condensingConnection for data exchange and remote controlled on and off: Ve.directParallel operation: Yes (not synchronized)PV connections 3): 35 mm² / AWG2Battery connections: 35mm² / AWG2Protection class: IP43 (electronic components), IP22 (connection area)Weight: 3kgDimensions (HXBXT): 185 x 250 x 95mm1a) If more PV current is connected, the controller limits the input performance.1b) The PV voltage must reach at least the amount of VBAT + 5 V so that the controller takes up the operation. Then the minimum value of the PV voltage is at VBAT + 1 V.2) A PV system with a higher short-circuit current can damage the controller.

Der BlueSolar 12/24V 10A-Laderegler ist eine zuverlässige Lösung für kleinere Solarsysteme. Er bietet grundlegende Schutzfunktionen und unterstützt sowohl 12V- als auch 24V-Systeme.Technische Daten:Spannung: 12/24VMaximalstrom: 10A.

Ultra fast Maximum Power Point Tracking (MPPT)Especially in overcast sky, when the light intensity is constantly changing, an extremely fast MPPT controller improves the energy yield as compared to PWM charge controllers by up to 30% and in comparison to slower MPPT controllers by up to 10%.Advanced maximum power point detection in partial shade.In case of partial shading of maximum power (MPP) may be present on the current-voltage curve two or more points.Conventional MPPTs tend to adapt to a local MPP.However, this might not be the optimum MPP.The innovative algorithm of BlueSolar device always maximize the energy yield by adjusts to the optimum MPP.outstanding efficiencyNo cooling fan. Maximum efficiency at over 98%. Full output power up to 40 ° C (104 ° F).Flexible charging algorithmsFully programmable charging algorithm (also refer to the software side of the Victron Energy website) and eight pre-programmed algorithms that can be selected via a rotary knob (for further details, see the manual).Comprehensive electronic protectionOverheating protection and power derating at high temperatures.Protection against PV short circuit and PV reverse polarity.PV reverse current protection.Internal temperature sensorCompensates constant and trickle charging voltages to temperature from.Options for displaying data in real time- Apple and Android smartphones, tablets and other devices: note the VE.Direct to Bluetooth Smart Dongle- Color Control PanelBattery voltage: 12/24 / 48V Auto Select (software tool required to select 36V)Nominal charging current: 60ANominal PV power, 12 V 1a, b): 860WRated PV power, 24V 1a, b): 1720WRated PV power, 48V 1a, b): 3440WMax. Short-circuit current solar system 2): 50AMaximum PV open voltage: 150V absolute maximum coldest conditions, 145 V maximum for power-up and operationMax. Efficiency: 98%Power consumption: 10mA"Constant" -Ladespannung (absorption) Standard settings: 14.4 / 28.8 / 43.2 / 57,6V (regulated)"Maintenance" -Ladespannung (float) Standard settings: 13.8 / 27.6 / 41.4 / 55,2V (regulated)Charging algorithm: multi-level, adaptiveTemperature compensation: -16mV / -32mV / -64mV / ° CProtection: reverse polarity of battery (backup, no access by the user) / PV reverse polarity / output short-circuit / temperatureOperating Temperature: -30 ° C to + 60 ° C (full rated output up to 40 ° C)Humidity: 95% non-condensingPort for data exchange and remote on and off: VE.DirectParallel operation: Yes (not synchronized)PV ports 3): Two sets of MC4 connectorBattery Terminals: 35mm² / AWG2Protection: IP43 (electronic components), IP22 (connection area)Weight: 3kgDimensions (HxWxD): 215 x 250 x 95mm1a) If more PV power is connected, the controller limits the input power.1b) The PV voltage must reach at least the height of Vbat + 5 V, so that the controller receives the operation. After that, the minimum value of the PV voltage at Vbat + 1 V. is2) A PV system with a higher short-circuit current can damage the controller.3) MC4 models: it may be necessary splitter to the strands of the solar modules to be connected in parallel several pairs. Maximum current per MC4 connector: 30 A (The MC4 connector are connected in parallel to a MPPT tracker) ^.

Der BlueSolar MPPT 150/100 ist ein leistungsstarker Laderegler, der speziell für größere Solaranlagen entwickelt wurde. Mit seiner MPPT-Technologie sorgt er für maximale Energieausbeute.Technische Daten:Spannung: 150VMaximalstrom: 100A.

Ultra fast Maximum Power Point Tracking (MPPT)Especially in overcast sky, when the light intensity is constantly changing, an extremely fast MPPT controller improves the energy yield as compared to PWM charge controllers by up to 30% and in comparison to slower MPPT controllers by up to 10%.Advanced maximum power point detection in partial shade.In case of partial shading of maximum power (MPP) may be present on the current-voltage curve two or more points.Conventional MPPTs tend to adapt to a local MPP.However, this might not be the optimum MPP.The innovative algorithm of BlueSolar device always maximize the energy yield by adjusts to the optimum MPP.outstanding efficiencyNo cooling fan. Maximum efficiency at over 98%. Full output power up to 40 ° C (104 ° F).Flexible charging algorithmsFully programmable charging algorithm (also refer to the software side of the Victron Energy website) and eight pre-programmed algorithms that can be selected via a rotary knob (for further details, see the manual).Comprehensive electronic protectionOverheating protection and power derating at high temperatures.Protection against PV short circuit and PV reverse polarity.PV reverse current protection.Internal temperature sensorCompensates constant and trickle charging voltages to temperature from.Options for displaying data in real time- Apple and Android smartphones, tablets and other devices: note the VE.Direct to Bluetooth Smart Dongle- Color Control PanelBattery voltage: 12/24 / 48V Auto Select (software tool required to select 36V)Nominal charging current: 70ANominal PV power, 12 V 1a, b): 1000WRated PV power, 24V 1a, b): 2000WRated PV power, 48V 1a, b): 4000WMax. Short-circuit current solar system 2): 50AMaximum PV open voltage: 150V absolute maximum coldest conditions, 145 V maximum for power-up and operationMax. Efficiency: 98%Power consumption: 10mA"Constant" -Ladespannung (absorption) Standard settings: 14.4 / 28.8 / 43.2 / 57,6V (regulated)"Maintenance" -Ladespannung (float) Standard settings: 13.8 / 27.6 / 41.4 / 55,2V (regulated)Charging algorithm: multi-level, adaptiveTemperature compensation: -16mV / -32mV / -64mV / ° CProtection: reverse polarity of battery (backup, no access by the user) / PV reverse polarity / output short-circuit / temperatureOperating Temperature: -30 ° C to + 60 ° C (full rated output up to 40 ° C)Humidity: 95% non-condensingPort for data exchange and remote on and off: VE.DirectParallel operation: Yes (not synchronized)PV ports 3): Two sets of MC4 connectorBattery Terminals: 35mm² / AWG2Protection: IP43 (electronic components), IP22 (connection area)Weight: 3kgDimensions (HxWxD): 215 x 250 x 95mm1a) If more PV power is connected, the controller limits the input power.1b) The PV voltage must reach at least the height of Vbat + 5 V, so that the controller receives the operation. After that, the minimum value of the PV voltage at Vbat + 1 V. is2) A PV system with a higher short-circuit current can damage the controller.3) MC4 models: it may be necessary splitter to the strands of the solar modules to be connected in parallel several pairs. Maximum current per MC4 connector: 30 A (The MC4 connector are connected in parallel to a MPPT tracker) ^.

Ultra -fast maximum power point tracking (mppt)Especially when the sky is covered, when the light intensity is constantly changing, an extremely fast MPPT controller improves the energy yield compared to PWM charging controls by up to 30% and compared to slower MPPT regulators by up to 10%.Advanced maximum Power Point detection in part shading.In the event of a partial shading, two or more points of maximum performance (MPP) may be available on the electricity voltage curve.Conventional MPTS tend to adjust to a local MPP.However, this may not be the optimal MPP.The innovative algorithm of the Bluesolar device will always maximize the energy yield by adjusting itself to the optimal MPP.Excellent efficiencyNo cooling fan. Maximum efficiency at over 98%. Full of output current up to 40 ° C (104 ° f).Flexible loading algorithmsFully programmable loading algorithm (also note the software page on the Victron Energy website) and eight pre-programmed algorithms that can be selected using a rotary knob (other details can be found in the manual).Comprehensive electronic protectionOverheating protection and load reduction at high temperatures.Protection against PV short circuit and PV solutions.PV backstream protection.Internal temperature sensorCompensates for constant and charging conservation voltages after temperature.Options for displaying data in real time- Apple and Android smartphones, tablets and other devices: Note the VE.Direct to Bluetooth Smart Dongle- Color Control panelBattery voltage: 12/24/48 V Autom. Selection (a software tool is required to select 36 V)Nominal power: 35 aName PV performance 1A, b): 12 V: 500 W / 24 V: 1000 W / 36 V: 1500 W / 48 V: 2000 WMax. PV short circuit current 2): 40AMaximum PV empty voltage: 150 V Absolute maximum Coldest conditions, 145 V maximum value for switching and operationMax. Effect: 98%Self -consumption 12V: 20 MA 24V: 15 MA 48V: 10MA"Constant" charging voltage (absorption) Standard settings: 14.4 / 28.8 / 43.2 / 57.6 V (regulable)"Conservation" charging voltage (float) Standard settings: 13.8 / 27.6 / 41.4 / 55.2 V (regulable)Ladeal gorithm: multi -stage, adaptiveTemperature compensation: -16 MV / -32 MV / -64 MV / ° CProtection: Polation on battery (backup, no access by the user), PV solutions, output short circuit, overheating, overheatingOperating temperature: -30 ° C to +60 ° C (full nominal output up to 40 ° C)Moisture: 95% not condensingData communication sport: ve.directConnections: 13 mm²/AWG6Protection class: IP43 (electronic components), IP22 (connection area)Weight: 1.25 kgDimensions (HXBXT): 130 x 186 x 70 mm1a) If more PV current is connected, the controller limits the input performance.1b) The PV voltage must reach at least the amount of VBAT + 5 V so that the controller takes up the operation. Then the minimum value of the PV voltage is at VBAT + 1 V.2) A PV system with a higher short-circuit current can damage the controller.

Der BlueSolar MPPT 250/100 VE.Can ist für große Solaranlagen ausgelegt. Mit seiner maximalen Eingangsspannung von 250V und einem Strom von 100A bietet er maximale Effizienz für komplexe Solarsysteme.Technische Daten:Spannung: 250VMaximalstrom: 100A.

Ultra -fast maximum power point tracking (mppt)Especially when the sky is covered, when the light intensity is constantly changing, an extremely fast MPPT controller improves the energy yield compared to PWM charging controls by up to 30% and compared to slower MPPT regulators by up to 10%.Advanced maximum Power Point detection in part shading.In the event of a partial shading, two or more points of maximum performance (MPP) may be available on the electricity voltage curve.Conventional MPTS tend to adjust to a local MPP.However, this may not be the optimal MPP.The innovative algorithm of the Bluesolar device will always maximize the energy yield by adjusting itself to the optimal MPP.Excellent efficiencyNo cooling fan. Maximum efficiency at over 98%. Full of output current up to 40 ° C (104 ° f).Flexible loading algorithmsFully programmable loading algorithm (also note the software page on the Victron Energy website) and eight pre-programmed algorithms that can be selected using a rotary knob (other details can be found in the manual).Comprehensive electronic protectionOverheating protection and load reduction at high temperatures.Protection against PV short circuit and PV solutions.PV backstream protection.Internal temperature sensorCompensates for constant and charging conservation voltages after temperature.Options for displaying data in real time- Apple and Android smartphones, tablets and other devices: Note the VE.Direct to Bluetooth Smart Dongle- Color Control panelBattery voltage: 12/24/48V Auto Select (software tool required to select 36V)Nominal power: 60aName PV performance, 12 V 1a, b): 860WName PV performance, 24V 1A, b): 1720WName PV performance, 48V 1A, b): 3440WMax. Short -circuit current solar system 2): 50AMaximum PV empty voltage: 150 V Absolute maximum Coldest conditions, 145 V maximum value for switching and operationMax. Effect: 98%Self -consumption: 10mA"Constant" charging voltage (absorption) Standard settings: 14.4 / 28.8 / 43.2 / 57.6V (regulable)"Conservation" charging voltage (float) Standard settings: 13.8 / 27.6 / 41.4 / 55.2V (regulable)Ladeal gorithm: multi -stage, adaptiveTemperature compensation: -16mv / -32mv / -64mv / ° CProtection: Polation to battery (backup, no access by the user) / PV solutions / output cocoing / over temperatureOperating temperature: -30 ° C to +60 ° C (full nominal output up to 40 ° C)Moisture: 95% not condensingConnection for data exchange and remote controlled on and off: Ve.directParallel operation: Yes (not synchronized)PV connections 3): 35 mm² / AWG2Battery connections: 35mm² / AWG2Protection class: IP43 (electronic components), IP22 (connection area)Weight: 3kgDimensions (HXBXT): 185 x 250 x 95mm1a) If more PV current is connected, the controller limits the input performance.1b) The PV voltage must reach at least the amount of VBAT + 5 V so that the controller takes up the operation. Then the minimum value of the PV voltage is at VBAT + 1 V.2) A PV system with a higher short-circuit current can damage the controller.

Ultra fast Maximum Power Point Tracking (MPPT)Especially in overcast sky, when the light intensity is constantly changing, an extremely fast MPPT controller improves the energy yield as compared to PWM charge controllers by up to 30% and in comparison to slower MPPTReglern by up to 10%.load outputA can be prevented by all loads are connected to the output load to deep discharge of the battery.The load output disconnects the loads when the battery has been up to a predetermined voltage value discharged.Alternatively, can also choose an algorithm for intelligent battery management: See Battery Life.The load output is short-circuit proof.Some loads (particularly inverter) can be connected directly to the battery at best.The inverter remote control is best to the load output connect. Under certain circumstances, a special interface cable is required, please refer to the manual.Battery Life: intelligent battery managementIf the solar charging controller is not able to charge the battery within one day up to its full capacity, the status of the battery changes constantly "partially loaded" and between "the end of discharge" back and forth.This mode of operation (no regular full charging) damaged a lead-acid battery within a few weeks or months.The Battery Life algorithm monitors the state of charge of the battery and, if necessary he lifts every day the threshold value for separating the load on (i. E., The load is disconnected earlier) until the recovered energy sufficient to charge the battery up to almost 100%.From this point, the threshold value is modulated for the disconnection of the load, so that the charging nearly 100% is achieved about once weekly.Programmable battery charging algorithmFor more information, see the section Software on the Victron Energy website.Day / night time control and light insulation optionFor more information, see the section Software on the Victron Energy website.Options for programming, real-time data and display the course- Modern Apple and Android smartphones, tablets, Macbooks and other devices: find screenshots for this purposeIn the info sheets of VE.Direct Bluetooth Smart dongle and the MPPT app.Battery voltage: 12 / 24V automatic selectionNominal charging current: 15ANominal PV power, 12 V 1a, b): 220WNominal PV power, 24 V 1a, b): 440WMax PV short-circuit current 2):. 15AAutomatic load disconnect Yes, maximum load 15AMaximum PV open voltage: 100VPeak efficiency: 98%Power consumption: 12V: 24V 20 mA: 10 mA"Constant" -Ladespannung (absorption): 14.4V / 28.8V (adjustable)"Conservation" -Ladespannung (float): 13.8V / 27.6V (adjustable)Charging algorithm: multi-level, adaptiveTemperature Compensation: -16 mV / ° C and -32 mV / ° CUninterrupted / peak load current: 15A / 50ASwitching off the load at a low voltage: 11.1V / 22,2V or 11.8V / or 23,6V Battery Life algorithmReconnecting the load to a low voltage: 13,1V / 26,2V or 14V / 28V or Battery Life algorithmProtection: Battery reverse polarity (fuse) Output short circuit / overheatingOperating Temperature: -30 ° C to + 60 ° C (full rated output up to 40 ° C)Humidity: 95% non-condensingData communication port: VE.DirectConnections: 6mm² / AWG10Protection: IP43 (electronic components), IP22 (connection regionWeight: 0.5kgDimensions (HxWxD): 100 x 113 x 40mm1a) If more PV power is connected, the controller limits the input power.1b) The PV voltage must at least the height of Vbat + reach 5V, so that the controller operation Tapes. After that, the minimum value of the PV voltage at Vbat + 1V.2) A PV system with a higher short-circuit current can damage the controller.

Ultra fast Maximum Power Point Tracking (MPPT)Especially in overcast sky, when the light intensity is constantly changing, an extremely fast MPPT controller improves the energy yield as compared to PWM charge controllers by up to 30% and in comparison to slower MPPT controllers by up to 10%.Advanced maximum power point detection in partial shade.In case of partial shading of maximum power (MPP) may be present on the current-voltage curve two or more points.Conventional MPPTs tend to adapt to a local MPP.However, this might not be the optimum MPP.The innovative algorithm of BlueSolar device always maximize the energy yield by adjusts to the optimum MPP.outstanding efficiencyNo cooling fan. Maximum efficiency at over 98%. Full output power up to 40 ° C (104 ° F).Flexible charging algorithmsFully programmable charging algorithm (also refer to the software side of the Victron Energy website) and eight pre-programmed algorithms that can be selected via a rotary knob (for further details, see the manual).Comprehensive electronic protectionOverheating protection and power derating at high temperatures.Protection against PV short circuit and PV reverse polarity.PV reverse current protection.Internal temperature sensorCompensates constant and trickle charging voltages to temperature from.Options for displaying data in real time- Apple and Android smartphones, tablets and other devices: note the VE.Direct to Bluetooth Smart Dongle- Color Control PanelBattery voltage: 12/24 V automatic selectionNominal charging current: 50ARated PV power, 12V 1a, b): 700WNominal PV power, 24 V 1a, b): 1400WMaximum PV open voltage: 100VMax PV short-circuit current 2):. 60APeak efficiency: 98%Power consumption 12V: 30 mA 24 V: 20 mA"Constant" -Ladespannung (absorption) Standard settings: 14.4 V / 28.8 V (regulated)"Maintenance" -Ladespannung (float) Standard settings: 13.8 V / 27.6 V (regulated)Charging algorithm: multi-level, adaptiveTemperature Compensation: -16 mV / ° C and -32 mV / ° CProtection: reverse polarity of battery (backup, no access by the user), PV reverse polarity, output short circuit, overheatingOperating Temperature: -30 ° C to + 60 ° C (full rated output up to 40 ° C)Humidity: 95% non-condensingData communication port: VE.DirectConnections: 13 mm² / AWG6Protection: IP43 (electronic components), IP22 (connection area)Weight: 1.3 kgDimensions (HxBxT): 130 x 186 x 70 mm1a) If more PV power is connected, the controller limits the input power.1b) The PV voltage must reach at least the height of Vbat + 5 V, so that the controller receives the operation. After that, the minimum value of the PV voltage at Vbat + 1 V. is2) A PV system with a higher short-circuit current can damage the controller.