Victron Phoenix Smart Ip43 Chargers

Power cable for Phoenix smart charger IP43Power Cord with Scghutzkontaktstecker and inlet socket

Phoenix smart charger IP4324 V, 3 outputs 24/25 (3)Ready for Bluetooth SmartChanging the settings and update the charger for newly available software functions capable Bluetooth with any smartphone, tablet or other device to be made.Phoenix Smart (3): three full current outputs to charge 3 battery banksAll outputs can supply the full rated output current.Automatic voltage compensationThe charger compensates a voltage drop across the DC cables by slightly increasing the output voltage when the DC current increases.For more details, see the manual.Adaptive five-stage charge algorithm: constant current - ( "bulk") phase, constant voltage - ( "absorption") phase recovery ( "recondition") phase, trickle charge voltage - ( "float") phase, bearing - voltage ( "storage") Phase:The Phoenix smart charger has our well-known "adaptive" 'battery management system that can be adapted to the different types of batteries. "Adaptive" means that the charging characteristic is automatically adjusted to the type of battery usage.The right amount of charge: variable absorption timeAt low battery discharge (. Eg a yacht connected to shore power) a short absorption time is selected to avoid overcharging.After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged.Preventing damage due to excessive gassing: The Battery Safe Mode (see Figure 2)In order to shorten the charging time, a high charge current was selected together with a high constant voltage.But this excessive gas evolution, the charger is avoided at the end of the constant current phase, limits the rate of voltage increase once the gassing voltage has been reached.Less maintenance and aging in the idle state of the battery: the storage modeThe storage mode is always activated when no discharge has taken place within 24 hours.in the storage mode, the trickle charge voltage is then reduced to 2.2 V / cell (13.2 V for a 24 V battery), in order to minimize gas evolution and corrosion of the positive plates.once a week the voltage is raised to the level of gassing.This achieves a sort of compensation charge, the electrolyte stratification and the sulfation - prevents - the two main reasons for premature battery failure.Loading and lithium-ion (LiFePO4) batteriesIt can be attached off control of an on / off by a relay or an optocoupler open collector output of a Li-Ion BMS for remote on / off port is connected.Alternatively, voltage and current can also fully control via Bluetooth.Fully programmable charging algorithmThe charging algorithm can be programmed via Bluetooth or via the VE.Direct interface.Using the MODE button you can select between three pre-programmed algorithms (see specifications).Remote On / OffThe remote on / off is composed of two terminals: Remote H and remote L.Between H and L a remote A may be on / off switch or relay are connected.Alternatively, the terminal H can be pulled or the terminal L can be pulled down.See manual for details.VE.Direct interfaceFor a wired data connection with a Color Control Panel, a PC or other devices.Note the VictronConnect app under Downloads / Software on Victron Energy website.programmable relayCan a Bluetooth-enabled device can be programmed via the VE.Direct interface or to trigger an alarm or other events.Technical specifications:Input voltage VAC 230 (range 210-250 V)DC input voltage range from 290 to 355 VDCFrequency 45 / -65 HzPower Factor 0.7Deduction recycle stream separated AC: connected <0.1 mA AC charger and remote control of: <6 mAPower consumption without load 1WEfficiency 94%"Constant" -Ladespannung (absorption): Normal: 28.8V / High: 29,4V / lithium ions: 28,4V"Maintenance" -Ladespannung (float): Normal: 27.6V / High: 27.6V / lithium ions: 27.0 VStorage mode: Normal: 26.4V / High: 26.4V / lithium ions: 27.0 VA charging current Hausbatterie25Low Power Mode 12.5 ACharging algorithm in five stages, adaptiveProtection: reverse polarity to the battery (backup, not accessible by the user) / output short circuit / temperatureCan be use as power supply: Yes, output voltage can be combined with Bluetooth and / or discontinue VE.Direct.Operating temperature range -20 to 60? (0-140 F) - rated output current of up to 40 ° C, deteriorates linearly to 20% at 60 ° CHumidity (non-condensing) max 95%Relay (programmable) DC current rating: 5 A up to 28 VDCBattery Connection screw 16 mm² (AWG6)AC outlet: IEC 320 C14 input with holder (AC-cable with country-specific plug must be ordered separately.)Protection class IP43 (electronic components), IP22 (connection area)Weight 3.5 kgDimensions (HxBxT) 180 x 249 x 100 mmFIGURE SIMILAR! AC POWER CORD (1973806) PLEASE ORDER SEPARATELY!

Phoenix Smart IP43 charger24 V, 2 outputs 24/25 (1+1)Ready for Bluetooth SmartChange the settings and updating the charger for newly available software functions can be carried out with any Bluetooth-enabled smartphone, tablet or other device.Phoenix Smart (1+1): Two outputs for charging two batteriesThe second output is intended for charging the starter battery. As a result, it is limited to 3 A and has a slightly lower output voltage for keeping loading the usually full starter battery.Automatic voltage compensationThe charger compensates for a voltage drop on the DC cables by slightly increasing the output voltage when the direct current increases.You can find more details in the manual.Adaptive five-stage loading algorithm: constant current-(“Bulk”) phase, constant voltage-(“absorption”) phase, restoration (“recondition”) phase, load maintenance voltage-(“float”) phase, warehouse voltage-(“storage”) phase:The Phoenix Smart charger has our well-known "adaptive" battery management system, which can be matched to the different types of battery. “Adaptive” means that the charging characteristic is automatically adjusted to the type of battery use.The correct amount of charging: variable constant stress phaseWith a low battery discharge (e.g. a yacht connected to country current), a short constant voltage phase is chosen to avoid an overload.After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged.Prevention of damage caused by excessive gastung: Batterysafe mode (see Figure 2)In order to shorten the loading time, the highest possible charging current was selected together with a high constant voltage.However, in order for an excessive gas development to be avoided towards the end of the constant trump phase, the charger limits the speed of the voltage increase after the gas voltage has been reached.Less maintenance and aging in the resting state of the battery: the storage modeThe warehouse mode is always activated if no discharge has been carried out within 24 hours.In storage mode, the loading voltage is then reduced to 2.2 V/cell (13.2 V for a 24 V battery) in order to minimize gas development and corrosion on the positive plates.Once a week, the voltage is increased to the level of the gas voltage.This achieves a kind of compensation charge that prevents the electrolystic layering and sulfating - the two main reasons for premature battery failure.Lithium ions (LIFEPO4) also loads batteriesA/off control can be installed by connecting a relay or an optocoupler output with an open collector by a Li-ion BMS to a remote-controlled one/output port.Alternatively, voltage and electricity can also be ruled completely via Bluetooth.Fully programmable charging algorithmThe loading algorithm can be programmed via Bluetooth or via VE.Direct interface.With the Mode button, you can choose between three pre -programmed algorithms (see technical information).Remote on/offThe remote on/off consists of two terminals: Remote H and Remote L.A remote/exterior switch or relay contact can be connected between H and L.Alternatively, the terminal H can be pulled up or the Terminal L can be pulled down.See manual for details.Ve.direct interfaceFor a wired data connection with a color control panel, a PC or other devices.Note the VictronConnect app under Downloads/Software on Victron Energy website.Programmable relayCan be programmed via the VE.Direct interface or a Bluetooth-compatible device to trigger an alarm or other events.Technical specifications:Input voltage 230 VAC (area 210-250 V)DC input voltage range 290-355 VDCFrequency 45/-65 HzPower factor 0.7Deduction Return current AC separated: <0.1 MA AC connected and remote control charger: <6 maElectricity consumption without load 1 wEffect 94%"Constant" charging voltage (absorption): normal: 28.8V / high: 29.4V / lithium ion: 28.4V"Conservation" charging voltage (float): normal: 27.6V / high: 27.6V / lithium ion: 27.0 VStorage mode: normal: 26.4V / high: 26.4V / lithium ion: 27.0 VCharging current house battery 25 aLow power mode 12.5 aCharging current starter battery 3 aLadeal gorithm five stages, adaptiveProtection: Polation on battery (backup, not accessible by the user) / output cocoing / over temperatureCan be used as a power supply: Yes, output voltage can be set with Bluetooth and/or Ve.direct.Operating temperature range -20 to 60? (0 - 140 f) - nominal output current up to 40 ° C, deteriorated linearly to 20 % at 60 ° CMoist (non -condensing) max 95 %Relay (programmable) DC Nodble value: 5 A up to 28 VDCBattery connection screw terminals 16 mm² (AWG6)AC connection: IEC 320 C14 input with bracket (AC cable with a country-specific connector must be ordered separately.)Protection class IP43 (electronic components), IP22 (connection area)Weight 3.5 kgDimensions (HXBXT) 180 x 249 x 100 mmFigure similar!AC network cable (1973806) Please order separately!

Phoenix Smart IP43 charger24 V, 3 outputs 24/16 (3)Ready for Bluetooth SmartChange the settings and updating the charger for newly available software functions can be carried out with any Bluetooth-enabled smartphone, tablet or other device.Phoenix Smart (3): Three full power outputs for charging 3 battery benchesAll outputs can deliver the full starting stone current.Automatic voltage compensationThe charger compensates for a voltage drop on the DC cables by slightly increasing the output voltage when the direct current increases.You can find more details in the manual.Adaptive five-stage loading algorithm: constant current-(“Bulk”) phase, constant voltage-(“absorption”) phase, restoration (“recondition”) phase, load maintenance voltage-(“float”) phase, warehouse voltage-(“storage”) phase:The Phoenix Smart charger has our well-known "adaptive" battery management system, which can be matched to the different types of battery. “Adaptive” means that the charging characteristic is automatically adjusted to the type of battery use.The correct amount of charging: variable constant stress phaseWith a low battery discharge (e.g. a yacht connected to country current), a short constant voltage phase is chosen to avoid an overload.After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged.Prevention of damage caused by excessive gastung: Batterysafe mode (see Figure 2)In order to shorten the loading time, the highest possible charging current was selected together with a high constant voltage.However, in order for an excessive gas development to be avoided towards the end of the constant trump phase, the charger limits the speed of the voltage increase after the gas voltage has been reached.Less maintenance and aging in the resting state of the battery: the storage modeThe warehouse mode is always activated if no discharge has been carried out within 24 hours.In storage mode, the loading voltage is then reduced to 2.2 V/cell (13.2 V for a 24 V battery) in order to minimize gas development and corrosion on the positive plates.Once a week, the voltage is increased to the level of the gas voltage.This achieves a kind of compensation charge that prevents the electrolystic layering and sulfating - the two main reasons for premature battery failure.Lithium ions (LIFEPO4) also loads batteriesA/off control can be installed by connecting a relay or an optocoupler output with an open collector by a Li-ion BMS to a remote-controlled one/output port.Alternatively, voltage and electricity can also be ruled completely via Bluetooth.Fully programmable charging algorithmThe loading algorithm can be programmed via Bluetooth or via VE.Direct interface.With the Mode button, you can choose between three pre -programmed algorithms (see technical information).Remote on/offThe remote on/off consists of two terminals: Remote H and Remote L.A remote/exterior switch or relay contact can be connected between H and L.Alternatively, the terminal H can be pulled up or the Terminal L can be pulled down.See manual for details.Ve.direct interfaceFor a wired data connection with a color control panel, a PC or other devices.Note the VictronConnect app under Downloads/Software on Victron Energy website.Programmable relayCan be programmed via the VE.Direct interface or a Bluetooth-compatible device to trigger an alarm or other events.Technical specifications:Input voltage 230 VAC (area 210-250 V)DC input voltage range 290-355 VDCFrequency 45/-65 HzPower factor 0.7Deduction Return current AC separated: <0.1 MA AC connected and remote control charger: <6 maElectricity consumption without load 1 wEffect 94%"Constant" charging voltage (absorption): normal: 28.8V / high: 29.4V / lithium ion: 28.4V"Conservation" charging voltage (float): normal: 27.6V / high: 27.6V / lithium ion: 27.0 VStorage mode: normal: 26.4V / high: 26.4V / lithium ion: 27.0 VCharging current house battery 16 aLow power mode 8 aLadeal gorithm five stages, adaptiveProtection: Polation on battery (backup, not accessible by the user) / output cocoing / over temperatureCan be used as a power supply: Yes, output voltage can be set with Bluetooth and/or Ve.direct.Operating temperature range -20 to 60? (0 - 140 f) - nominal exit current up to 40 ° C, deteriorated linearly to 20 % at 60 ° C^Moist (non -condensing) max 95 %Relay (programmable) DC Nodble value: 5 A up to 28 VDCBattery connection screw terminals 16 mm² (AWG6)AC connection: IEC 320 C14 input with bracket (AC cable with a country-specific connector must be ordered separately.)Protection class IP43 (electronic components), IP22 (connection area)Weight 3.5 kgDimensions (HXBXT) 180 x 249 x 100 mmFigure similar!AC network cable (1973806) Please order separately!

Phoenix smart charger IP4324 V, 2 outputs 24/16 (1 + 1)Ready for Bluetooth SmartChanging the settings and update the charger for newly available software functions capable Bluetooth with any smartphone, tablet or other device to be made.Phoenix Smart (1 + 1): two outputs for charging two battery banksThe second output is provided to charge the starter battery. Consequently, it is limited to 3 A and has a slightly lower output voltage to the load results in no generally starter battery.Automatic voltage compensationThe charger compensates a voltage drop across the DC cables by slightly increasing the output voltage when the DC current increases.For more details, see the manual.Adaptive five-stage charge algorithm: constant current - ( "bulk") phase, constant voltage - ( "absorption") phase recovery ( "recondition") phase, trickle charge voltage - ( "float") phase, bearing - voltage ( "storage") Phase:The Phoenix smart charger has our well-known "adaptive" 'battery management system that can be adapted to the different types of batteries. "Adaptive" means that the charging characteristic is automatically adjusted to the type of battery usage.The right amount of charge: variable absorption timeAt low battery discharge (. Eg a yacht connected to shore power) a short absorption time is selected to avoid overcharging.After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged.Preventing damage due to excessive gassing: The Battery Safe Mode (see Figure 2)In order to shorten the charging time, a high charge current was selected together with a high constant voltage.But this excessive gas evolution, the charger is avoided at the end of the constant current phase, limits the rate of voltage increase once the gassing voltage has been reached.Less maintenance and aging in the idle state of the battery: the storage modeThe storage mode is always activated when no discharge has taken place within 24 hours.in the storage mode, the trickle charge voltage is then reduced to 2.2 V / cell (13.2 V for a 24 V battery), in order to minimize gas evolution and corrosion of the positive plates.once a week the voltage is raised to the level of gassing.This achieves a sort of compensation charge, the electrolyte stratification and the sulfation - prevents - the two main reasons for premature battery failure.Loading and lithium-ion (LiFePO4) batteriesIt can be attached off control of an on / off by a relay or an optocoupler open collector output of a Li-Ion BMS for remote on / off port is connected.Alternatively, voltage and current can also fully control via Bluetooth.Fully programmable charging algorithmThe charging algorithm can be programmed via Bluetooth or via the VE.Direct interface.Using the MODE button you can select between three pre-programmed algorithms (see specifications).Remote On / OffThe remote on / off is composed of two terminals: Remote H and remote L.Between H and L a remote A may be on / off switch or relay are connected.Alternatively, the terminal H can be pulled or the terminal L can be pulled down.See manual for details.VE.Direct interfaceFor a wired data connection with a Color Control Panel, a PC or other devices.Note the VictronConnect app under Downloads / Software on Victron Energy website.programmable relayCan a Bluetooth-enabled device can be programmed via the VE.Direct interface or to trigger an alarm or other events.Technical specifications:Input voltage VAC 230 (range 210-250 V)DC input voltage range from 290 to 355 VDCFrequency 45 / -65 HzPower Factor 0.7Deduction recycle stream separated AC: connected <0.1 mA AC charger and remote control of: <6 mAPower consumption without load 1WEfficiency 94%"Constant" -Ladespannung (absorption): Normal: 28.8V / High: 29,4V / lithium ions: 28,4V"Maintenance" -Ladespannung (float): Normal: 27.6V / High: 27.6V / lithium ions: 27.0 VStorage mode: Normal: 26.4V / High: 26.4V / lithium ions: 27.0 VCharging current house battery 16 ALow current mode 8 AA starter battery charging current 3Charging algorithm in five stages, adaptiveProtection: reverse polarity to the battery (backup, not accessible by the user) / output short circuit / temperatureCan be use as power supply: Yes, output voltage can be combined with Bluetooth and / or discontinue VE.Direct.Operating temperature range -20 to 60? (0-140 F) - rated output current of up to 40 ° C, deteriorates linearly to 20% at 60 ° CHumidity (non-condensing) max 95%Relay (programmable) DC current rating: 5 A up to 28 VDCBattery Connection screw 16 mm² (AWG6)AC outlet: IEC 320 C14 input with holder (AC-cable with country-specific plug must be ordered separately.)Protection class IP43 (electronic components), IP22 (connection area)Weight 3.5 kgDimensions (HxBxT) 180 x 249 x 100 mmFIGURE SIMILAR! AC POWER CORD (1973806) PLEASE ORDER SEPARATELY!

Phoenix smart charger IP4312 V, 3 outputs 12/50 (3)Ready for Bluetooth SmartChanging the settings and update the charger for newly available software functions capable Bluetooth with any smartphone, tablet or other device to be made.Phoenix Smart (3): three full current outputs to charge 3 battery banksAll outputs can supply the full rated output current.Automatic voltage compensationThe charger compensates a voltage drop across the DC cables by slightly increasing the output voltage when the DC current increases.For more details, see the manual.Adaptive five-stage charge algorithm: constant current - ( "bulk") phase, constant voltage - ( "absorption") phase recovery ( "recondition") phase, trickle charge voltage - ( "float") phase, bearing - voltage ( "storage") Phase:The Phoenix smart charger has our well-known "adaptive" 'battery management system that can be adapted to the different types of batteries. "Adaptive" means that the charging characteristic is automatically adjusted to the type of battery usage.The right amount of charge: variable absorption timeAt low battery discharge (. Eg a yacht connected to shore power) a short absorption time is selected to avoid overcharging.After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged.Preventing damage due to excessive gassing: The Battery Safe Mode (see Figure 2)In order to shorten the charging time, a high charge current was selected together with a high constant voltage.But this excessive gas evolution, the charger is avoided at the end of the constant current phase, limits the rate of voltage increase once the gassing voltage has been reached.Less maintenance and aging in the idle state of the battery: the storage modeThe storage mode is always activated when no discharge has taken place within 24 hours.in the storage mode, the trickle charge voltage is then reduced to 2.2 V / cell (13.2 V for a 24 V battery), in order to minimize gas evolution and corrosion of the positive plates.once a week the voltage is raised to the level of gassing.This achieves a sort of compensation charge, the electrolyte stratification and the sulfation - prevents - the two main reasons for premature battery failure.Loading and lithium-ion (LiFePO4) batteriesIt can be attached off control of an on / off by a relay or an optocoupler open collector output of a Li-Ion BMS for remote on / off port is connected.Alternatively, voltage and current can also fully control via Bluetooth.Fully programmable charging algorithmThe charging algorithm can be programmed via Bluetooth or via the VE.Direct interface.Using the MODE button you can select between three pre-programmed algorithms (see specifications).Remote On / OffThe remote on / off is composed of two terminals: Remote H and remote L.Between H and L a remote A may be on / off switch or relay are connected.Alternatively, the terminal H can be pulled or the terminal L can be pulled down.See manual for details.VE.Direct interfaceFor a wired data connection with a Color Control Panel, a PC or other devices.Note the VictronConnect app under Downloads / Software on Victron Energy website.programmable relayCan a Bluetooth-enabled device can be programmed via the VE.Direct interface or to trigger an alarm or other events.Technical specifications:Input voltage VAC 230 (range 210-250 V)DC input voltage range from 290 to 355 VDCFrequency 45 / -65 HzPower Factor 0.7Deduction recycle stream separated AC: connected <0.1 mA AC charger and remote control of: <6 mAPower consumption without load 1WEfficiency 92%"Constant" -Ladespannung (absorption): Normal: 14.4 V / High: 14.7V / lithium ions: 14.2 V"Maintenance" -Ladespannung (float): Normal: 13.8 V / high: 13,8 / lithium ions: 13.5 VStorage mode: Normal: 13.2V / High: 13.2V / lithium ions: 13.5 VCharging current house battery 50 ALow-power mode 25 ACharging algorithm in five stages, adaptiveProtection: reverse polarity to the battery (backup, not accessible by the user) / output short circuit / temperatureCan be use as power supply: Yes, output voltage can be combined with Bluetooth and / or discontinue VE.Direct.Operating temperature range -20 to 60? (0-140 F) - rated output current of up to 40 ° C, deteriorates linearly to 20% at 60 ° CHumidity (non-condensing) max 95%Relay (programmable) DC current rating: 5 A up to 28 VDCBattery Connection screw 16 mm² (AWG6)AC outlet: IEC 320 C14 input with holder (AC-cable with country-specific plug must be ordered separately.)Protection class IP43 (electronic components), IP22 (connection area)Weight 3.5 kgDimensions (HxBxT) 180 x 249 x 100 mmAC POWER CORD (1973806) PLEASE ORDER SEPARATELY!

Phoenix smart charger IP4312 V, 3 outputs 12/30 (3)Ready for Bluetooth SmartChanging the settings and update the charger for newly available software functions capable Bluetooth with any smartphone, tablet or other device to be made.Phoenix Smart (3): three full current outputs to charge 3 battery banksAll outputs can supply the full rated output current.Automatic voltage compensationThe charger compensates a voltage drop across the DC cables by slightly increasing the output voltage when the DC current increases.For more details, see the manual.Adaptive five-stage charge algorithm: constant current - ( "bulk") phase, constant voltage - ( "absorption") phase recovery ( "recondition") phase, trickle charge voltage - ( "float") phase, bearing - voltage ( "storage") Phase:The Phoenix smart charger has our well-known "adaptive" 'battery management system that can be adapted to the different types of batteries. "Adaptive" means that the charging characteristic is automatically adjusted to the type of battery usage.The right amount of charge: variable absorption timeAt low battery discharge (. Eg a yacht connected to shore power) a short absorption time is selected to avoid overcharging.After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged.Preventing damage due to excessive gassing: The Battery Safe Mode (see Figure 2)In order to shorten the charging time, a high charge current was selected together with a high constant voltage.But this excessive gas evolution, the charger is avoided at the end of the constant current phase, limits the rate of voltage increase once the gassing voltage has been reached.Less maintenance and aging in the idle state of the battery: the storage modeThe storage mode is always activated when no discharge has taken place within 24 hours.in the storage mode, the trickle charge voltage is then reduced to 2.2 V / cell (13.2 V for a 24 V battery), in order to minimize gas evolution and corrosion of the positive plates.once a week the voltage is raised to the level of gassing.This achieves a sort of compensation charge, the electrolyte stratification and the sulfation - prevents - the two main reasons for premature battery failure.Loading and lithium-ion (LiFePO4) batteriesIt can be attached off control of an on / off by a relay or an optocoupler open collector output of a Li-Ion BMS for remote on / off port is connected.Alternatively, voltage and current can also fully control via Bluetooth.Fully programmable charging algorithmThe charging algorithm can be programmed via Bluetooth or via the VE.Direct interface.Using the MODE button you can select between three pre-programmed algorithms (see specifications).Remote On / OffThe remote on / off is composed of two terminals: Remote H and remote L.Between H and L a remote A may be on / off switch or relay are connected.Alternatively, the terminal H can be pulled or the terminal L can be pulled down.See manual for details.VE.Direct interfaceFor a wired data connection with a Color Control Panel, a PC or other devices.Note the VictronConnect app under Downloads / Software on Victron Energy website.programmable relayCan a Bluetooth-enabled device can be programmed via the VE.Direct interface or to trigger an alarm or other events.Technical specifications:Input voltage VAC 230 (range 210-250 V)DC input voltage range from 290 to 355 VDCFrequency 45 / -65 HzPower Factor 0.7Deduction recycle stream separated AC: connected <0.1 mA AC charger and remote control of: <6 mAPower consumption without load 1WEfficiency 94%"Constant" -Ladespannung (absorption): Normal: 14.4 V / High: 14.7V / lithium ions: 14.2 V"Maintenance" -Ladespannung (float): Normal: 13.8 V / high: 13,8 / lithium ions: 13.5 VStorage mode: Normal: 13.2V / High: 13.2V / lithium ions: 13.5 VCharging current house battery 30 A15 A low power modeCharging algorithm in five stages, adaptiveProtection: reverse polarity to the battery (backup, not accessible by the user) / output short circuit / temperatureCan be use as power supply: Yes, output voltage can be combined with Bluetooth and / or discontinue VE.Direct.Operating temperature range -20 to 60? (0-140 F) - rated output current of up to 40 ° C, deteriorates linearly to 20% at 60 ° CHumidity (non-condensing) max 95%Relay (programmable) DC current rating: 5 A up to 28 VDCBattery Connection screw 16 mm² (AWG6)AC outlet: IEC 320 C14 input with holder (AC-cable with country-specific plug must be ordered separately.)Protection class IP43 (electronic components), IP22 (connection area)Weight 3.5 kgDimensions (HxBxT) 180 x 249 x 100 mmAC POWER CORD (1973806) PLEASE ORDER SEPARATELY!

Phoenix smart charger IP4312 V, 2 outputs 12/50 (1 + 1)Ready for Bluetooth SmartChanging the settings and update the charger for newly available software functions capable Bluetooth with any smartphone, tablet or other device to be made.Phoenix Smart (1 + 1): two outputs for charging two battery banksThe second output is provided to charge the starter battery. Consequently, it is limited to 3 A and has a slightly lower output voltage to the load results in no generally starter battery.Automatic voltage compensationThe charger compensates a voltage drop across the DC cables by slightly increasing the output voltage when the DC current increases.For more details, see the manual.Adaptive five-stage charge algorithm: constant current - ( "bulk") phase, constant voltage - ( "absorption") phase recovery ( "recondition") phase, trickle charge voltage - ( "float") phase, bearing - voltage ( "storage") Phase:The Phoenix smart charger has our well-known "adaptive" 'battery management system that can be adapted to the different types of batteries. "Adaptive" means that the charging characteristic is automatically adjusted to the type of battery usage.The right amount of charge: variable absorption timeAt low battery discharge (. Eg a yacht connected to shore power) a short absorption time is selected to avoid overcharging.After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged.Preventing damage due to excessive gassing: The Battery Safe Mode (see Figure 2)In order to shorten the charging time, a high charge current was selected together with a high constant voltage.But this excessive gas evolution, the charger is avoided at the end of the constant current phase, limits the rate of voltage increase once the gassing voltage has been reached.Less maintenance and aging in the idle state of the battery: the storage modeThe storage mode is always activated when no discharge has taken place within 24 hours.in the storage mode, the trickle charge voltage is then reduced to 2.2 V / cell (13.2 V for a 24 V battery), in order to minimize gas evolution and corrosion of the positive plates.once a week the voltage is raised to the level of gassing.This achieves a sort of compensation charge, the electrolyte stratification and the sulfation - prevents - the two main reasons for premature battery failure.Loading and lithium-ion (LiFePO4) batteriesIt can be attached off control of an on / off by a relay or an optocoupler open collector output of a Li-Ion BMS for remote on / off port is connected.Alternatively, voltage and current can also fully control via Bluetooth.Fully programmable charging algorithmThe charging algorithm can be programmed via Bluetooth or via the VE.Direct interface.Using the MODE button you can select between three pre-programmed algorithms (see specifications).Remote On / OffThe remote on / off is composed of two terminals: Remote H and remote L.Between H and L a remote A may be on / off switch or relay are connected.Alternatively, the terminal H can be pulled or the terminal L can be pulled down.See manual for details.VE.Direct interfaceFor a wired data connection with a Color Control Panel, a PC or other devices.Note the VictronConnect app under Downloads / Software on Victron Energy website.programmable relayCan a Bluetooth-enabled device can be programmed via the VE.Direct interface or to trigger an alarm or other events.Technical specifications:Input voltage VAC 230 (range 210-250 V)DC input voltage range from 290 to 355 VDCFrequency 45 / -65 HzPower Factor 0.7Deduction recycle stream separated AC: connected <0.1 mA AC charger and remote control of: <6 mAPower consumption without load 1WEfficiency 92%"Constant" -Ladespannung (absorption): Normal: 14.4 V / High: 14.7V / lithium ions: 14.2 V"Maintenance" -Ladespannung (float): Normal: 13.8 V / high: 13,8 / lithium ions: 13.5 VStorage mode: Normal: 13.2V / High: 13.2V / lithium ions: 13.5 VCharging current house battery 50 ALow-power mode 25 AA starter battery charging current 3Charging algorithm in five stages, adaptiveProtection: reverse polarity to the battery (backup, not accessible by the user) / output short circuit / temperatureCan be use as power supply: Yes, output voltage can be combined with Bluetooth and / or discontinue VE.Direct.Operating temperature range -20 to 60? (0-140 F) - rated output current of up to 40 ° C, deteriorates linearly to 20% at 60 ° CHumidity (non-condensing) max 95%Relay (programmable) DC current rating: 5 A up to 28 VDCBattery Connection screw 16 mm² (AWG6)AC outlet: IEC 320 C14 input with holder (AC-cable with country-specific plug must be ordered separately.)Protection class IP43 (electronic components), IP22 (connection area)Weight 3.5 kgDimensions (HxBxT) 180 x 249 x 100 mmAC POWER CORD (1973806) PLEASE ORDER SEPARATELY!

Phoenix Smart IP43 charger12 V, 2 outputs 12/30 (1+1)Ready for Bluetooth SmartChange the settings and updating the charger for newly available software functions can be carried out with any Bluetooth-enabled smartphone, tablet or other device.Phoenix Smart (1+1): Two outputs for charging two batteriesThe second output is intended for charging the starter battery. As a result, it is limited to 3 A and has a slightly lower output voltage for keeping loading the usually full starter battery.Automatic voltage compensationThe charger compensates for a voltage drop on the DC cables by slightly increasing the output voltage when the direct current increases.You can find more details in the manual.Adaptive five-stage loading algorithm: constant current-(“Bulk”) phase, constant voltage-(“absorption”) phase, restoration (“recondition”) phase, load maintenance voltage-(“float”) phase, warehouse voltage-(“storage”) phase:The Phoenix Smart charger has our well-known "adaptive" battery management system, which can be matched to the different types of battery. “Adaptive” means that the charging characteristic is automatically adjusted to the type of battery use.The correct amount of charging: variable constant stress phaseWith a low battery discharge (e.g. a yacht connected to country current), a short constant voltage phase is chosen to avoid an overload.After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged.Prevention of damage caused by excessive gastung: Batterysafe mode (see Figure 2)In order to shorten the loading time, the highest possible charging current was selected together with a high constant voltage.However, in order for an excessive gas development to be avoided towards the end of the constant trump phase, the charger limits the speed of the voltage increase after the gas voltage has been reached.Less maintenance and aging in the resting state of the battery: the storage modeThe warehouse mode is always activated if no discharge has been carried out within 24 hours.In storage mode, the loading voltage is then reduced to 2.2 V/cell (13.2 V for a 24 V battery) in order to minimize gas development and corrosion on the positive plates.Once a week, the voltage is increased to the level of the gas voltage.This achieves a kind of compensation charge that prevents the electrolystic layering and sulfating - the two main reasons for premature battery failure.Lithium ions (LIFEPO4) also loads batteriesA/off control can be installed by connecting a relay or an optocoupler output with an open collector by a Li-ion BMS to a remote-controlled one/output port.Alternatively, voltage and electricity can also be ruled completely via Bluetooth.Fully programmable charging algorithmThe loading algorithm can be programmed via Bluetooth or via VE.Direct interface.With the Mode button, you can choose between three pre -programmed algorithms (see technical information).Remote on/offThe remote on/off consists of two terminals: Remote H and Remote L.A remote/exterior switch or relay contact can be connected between H and L.Alternatively, the terminal H can be pulled up or the Terminal L can be pulled down.See manual for details.Ve.direct interfaceFor a wired data connection with a color control panel, a PC or other devices.Note the VictronConnect app under Downloads/Software on Victron Energy website.Programmable relayCan be programmed via the VE.Direct interface or a Bluetooth-compatible device to trigger an alarm or other events.Technical specifications:Input voltage 230 VAC (area 210-250 V)DC input voltage range 290-355 VDCFrequency 45/-65 HzPower factor 0.7Deduction Return current AC separated: <0.1 MA AC connected and remote control charger: <6 maElectricity consumption without load 1 wEffect 94%"Constant" charging voltage (absorption): Normal: 14.4 V / high: 14.7V / lithium ions: 14.2 V"Conservation" charging voltage (float): normal: 13.8 V / high: 13.8V / lithium ion: 13.5 VStorage mode: normal: 13.2V / high: 13.2V / lithium ion: 13.5 VCharging current house battery 30 aLow power mode 15 aCharging current starter battery 3 aLadeal gorithm five stages, adaptiveProtection: Polation on battery (backup, not accessible by the user) / output cocoing / over temperatureCan be used as a power supply: Yes, output voltage can be set with Bluetooth and/or Ve.direct.Operating temperature range -20 to 60? (0 - 140 f) - nominal output current up to 40 ° C, deteriorated linearly to 20 % at 60 ° CMoist (non -condensing) max 95 %Relay (programmable) DC Nodble value: 5 A up to 28 VDCBattery connection screw terminals 16 mm² (AWG6)AC connection: IEC 320 C14 input with bracket (AC cable with a country-specific connector must be ordered separately.)Protection class IP43 (electronic components), IP22 (connection area)Weight 3.5 kgDimensions (HXBXT) 180 x 249 x 100 mmAC network cable (1973806) Please order separately!