Victron - MultiPlus 12V DC

The multi-inverter is a small compact inverter and charger at an attractive price.2 Output for charging of the starter battery is provided, the temperature sensor can also be angeschloseen, devices work with a temperatugesteuerten fan turns on when necessary.Weight: 4.4 kgDimensions: 311x182x100mm

The Multiplus is a powerful inverter with a pure sinus wave, an advanced battery loader that uses adaptive charging technology, and a high-speed change voltage transfer switch in a single compact housing. Apart from these primary functions, the Multiplus also offers several extended functions, which are explained below.Two alternating current outputs: The main exit ensures uninterrupted operation. In the event of a network failure or if the land/generator current is interrupted, the Multiplus takes over the supply of the connected consumers. Switching happens so quickly (in less than 20 milliseconds) that an interruption -free operation of computers and other electronic devices is guaranteed. The second output only provides electricity if there is an alternating current available on one of the inputs of the Multiplus AC. Consumers who are not allowed to unload the battery, such as B. a water heater can be connected to this output (a second output is only available for models with an output power of 3000 VA and more).Practically unlimited performance through parallel circuit: up to six multis can be switched in parallel with high power requirements.Three phase operation: Apart from the parallel connection, three units of the same model can also be configured for a three-phase output.PowerControl: Working with limited generator performance, limited land or network current. With the remote control panel Multi Control, the maximum network or generator current can be set. The Multiplus then takes into account other connected alternating current consumers and only uses the electricity that is still "left". This prevents the generator or the land power connection from being overloaded.Power Assist: With this function, the PowerControl principle receives a new dimension. It enables the multiplus to support too weak alternative sources. Load tips often only occur for a limited period of time. In such a case, the Multiplus ensures that too weak land electricity or generator output is immediately compensated for by energy from the battery. The load is reduced, i.e. H. If consumers are switched off, the energy that is then sufficiently existing can be used again to load the batteries.Four-stage adaptive charger and loading of two batteries: The main output using the advanced "adaptive charging" software ensures that the battery system is powerful. Another fourth stage for long periods of time in conservation mode. Apart from that, the Multiplus also loads a second battery by using an independent maintenance load output (conservation load output only available from 12 V and 24 V models). If settings have to be changed, this can be changed within of a few minutes using the new DIP switch setting process.Multi Plus - battery voltage 12 V 12/3000/120-50- Power Control / Power Assist: Yes- Transfer switch: 50 a-Parallel circuit and three-phase operation: Javerwichter- Input voltage area: 9.5–17 V (V DC)- Exit: output voltage: 230 V AC ± 2%, frequency: 50 Hz ± 0.1%- Kont. Output power at 25 ° C: 3000 VA **- Kont. Output power. at 25 ° C: 2500 W- Kont. Output power. at 40 ° C: 2200 W- Top performance: 6000 W- Max. Effect: 93 %- Zero-load performance: 15 W-Zero-load performance in AES mode: 10W-Zero-load performance in search mode: 4 wladitor-AC input: Input voltage area: 187-265VAC, input frequency: 45–65 Hz / performance factor: 1- Constant charging voltage: 14.4 V DC- Conservation charging voltage: 13.8 V DC- Storage mode: 13.2 V DC- charging current house battery: 120 a-Charging current Starter battery: 4 Abatter Temperature Sensor: Yes- General- Additional outcome (A): Yes (16 a)- Programmable relay: relay adjustable and a. As an alarm relay or start / stop function for an aggregate-Protection: output ceiling, overload, battery overvoltage, battery sub voltage, over temperature, 230 V AC at the inverter output, too high humming voltage at the input- Ve. Bus interface: for parallel circuits and three-phase operation, remote monitoring and system integration- Com port for general use: on request- Common features: operating temperature range: -20 to +50 ° C (blower testing), protection class: IP21-Battery connection: Four M8 bolts (2+ / 2-)- 230 V AC connection: screw terminals 13 mm²- Weight: 18 kg- Dimensions (HXBXT): 362 x 258 x 218 mm ** Nonlinear load, top factor 3: 1

The Multiplus is a powerful inverter with a pure sinus wave, an advanced battery loader that uses adaptive charging technology, and a high-speed change voltage transfer switch in a single compact housing. Apart from these primary functions, the Multiplus also offers several extended functions, which are explained below.Two alternating current outputs: The main exit ensures uninterrupted operation. In the event of a network failure or if the land/generator current is interrupted, the Multiplus takes over the supply of the connected consumers. Switching happens so quickly (in less than 20 milliseconds) that an interruption -free operation of computers and other electronic devices is guaranteed. The second output only provides electricity if there is an alternating current available on one of the inputs of the Multiplus AC. Consumers who are not allowed to unload the battery, such as B. a water heater can be connected to this output (a second output is only available for models with an output power of 3000 VA and more).Practically unlimited performance through parallel circuit: up to six multis can be switched in parallel with high power requirements.Three phase operation: Apart from the parallel connection, three units of the same model can also be configured for a three-phase output.PowerControl: Working with limited generator performance, limited land or network current. With the remote control panel Multi Control, the maximum network or generator current can be set. The Multiplus then takes into account other connected alternating current consumers and only uses the electricity that is still "left". This prevents the generator or the land power connection from being overloaded.Power Assist: With this function, the PowerControl principle receives a new dimension. It enables the multiplus to support too weak alternative sources. Load tips often only occur for a limited period of time. In such a case, the Multiplus ensures that too weak land electricity or generator output is immediately compensated for by energy from the battery. The load is reduced, i.e. H. If consumers are switched off, the energy that is then sufficiently existing can be used again to load the batteries.Four-stage adaptive charger and loading of two batteries: The main output using the advanced "adaptive charging" software ensures that the battery system is powerful. Another fourth stage for long periods of time in conservation mode. Apart from that, the Multiplus also loads a second battery by using an independent maintenance load output (conservation load output only available from 12 V and 24 V models). If settings have to be changed, this can be changed within of a few minutes using the new DIP switch setting process.Multi Plus - battery voltage 12 V 12/3000/120-16- Power Control / Power Assist: Yes- Transfer switch: 16 a-Parallel circuit and three-phase operation: Javerwichter- Input voltage area: 9.5–17 V (V DC)- Exit: output voltage: 230 V AC ± 2%, frequency: 50 Hz ± 0.1%- Kont. Output power at 25 ° C: 3000 VA **- Kont. Output power. at 25 ° C: 2500 W- Kont. Output power. at 40 ° C: 2200 W- Top performance: 6000 W- Max. Effect: 93 %- Zero-load performance: 15 W-Zero-load performance in AES mode: 10W-Zero-load performance in search mode: 4 wladitor-AC input: Input voltage area: 187-265VAC, input frequency: 45–65 Hz / performance factor: 1- Constant charging voltage: 14.4 V DC- Conservation charging voltage: 13.8 V DC- Storage mode: 13.2 V DC- charging current house battery: 120 a- Charging current starter battery: 4 a-Battery temperature sensor: Jaall community- Additional outcome (A): Yes (16 a)- Programmable relay: relay adjustable and a. As an alarm relay or start / stop function for an aggregate-Protection: output ceiling, overload, battery overvoltage, battery sub voltage, over temperature, 230 V AC at the inverter output, too high humming voltage at the input- Ve. Bus interface: for parallel circuits and three-phase operation, remote monitoring and system integration- Com port for general use: on request- Common features: operating temperature range: -20 to +50 ° C (blower testing), protection class: IP21-Battery connection: Four M8 bolts (2+ / 2-)- 230 V AC connection: screw terminals 13 mm²- Weight: 18 kg- Dimensions (HXBXT): 362 x 258 x 218 mm ** Nonlinear load, top factor 3: 1

The multi-Plus is a powerful inverter with pure sine wave, an advanced battery charger, which uses the adaptive charging technology, and a high-speed AC voltage transfer switch in a single compactCasing. Apart from these primary functions, the MultiPlus offers even more advanced features that are explained below.Two AC outputs: the main output provides uninterrupted operation. In the event of a power failure or an interruption of the shore / generator power the MultiPlus takes over the supply to the connected loads. This happens so quickly (in less than 20 milliseconds) that a continuous operation is ensured of computers and other electronic devices. The second output is only supplies current when the multi-Plus AC power is available at one of the inputs. Loads that should not discharge the battery, such. be as a water heater, can be connected to this output (second output is only available in models with an output power of 3000 VA and more).Practically unlimited performance using parallel circuit: up to six MNCs can be connected in parallel at high power requirements.Three phase operation: Apart from the parallel port can also three units of the same model for a three-phase output can be configured.Power Control: Dealing with limited generator, shore side or grid power. With the Multi Control Panel can be adjusted to the maximum generator or shore power. The MultiPlus will then take account of other AC loads and uses to charge only the current that is still "left". Thus, preventing the generator or shore supply from being overloaded.Power Assist: This feature allows the power control principle on a new dimension. It allows the MultiPlus to support capacity of the alternative sources. Peak power is so often required only for a limited period. In such a case, the multi-Plus ensure that a compensating insufficient shore or generator power immediately by energy from the battery. If the load is reduced, d. H. Consumers are turned off, then back enough available energy can be used to charge the batteries.Four stage adaptive charger and two batteries: The main output makes using the advanced "adaptive charging" software for a powerful charge to the battery system software fine-tunes the automatic three-stage charging process in order to adapt it to best suit the battery status In addition, it adds.. a fourth stage added for long periods of float charging. Besides that invites the MultiPlus even a second battery by using an independent trickle charge output (trickle charge output only at 12 V and 24 V models available). If settings have to be changed, this can be within a few minutes using carried the new DIP switch setting procedure.MultiPlus- Battery voltage 12 V C 12/2000 / 80-30- Power Control / Power Assist: yes- Transfer switch: 30 A- parallel and three-phase operation: yesINVERTER- Input voltage range: 9.5 to 17 V (VDC)- Output: Output voltage: 230 V AC ± 2% Frequency: 50 Hz ± 0.1%- cont. Output power at 25 ° C: 2000 VA **- cont. Ausgangsleistg. at 25 ° C: 1600 W- cont. Ausgangsleistg. at 40 ° C: 1450 W- Peak power: 4000 W- Max. Efficiency: 93%- Zero-load power: 9 W- Zero-load power in AES mode: 7 W- Zero-load power in search mode: 3 WCHARGER- AC input: Input voltage range: 187-265VAC, input frequency: 45-65 Hz / Power Factor: 1- Constant Charging Voltage: 14.4 V DC- Conservation charging voltage: 13.8 V DC- Storage mode: 13.2 V DC- Charge current house battery: 80 A- Charge current starter battery: 4 A- Battery temperature sensor: yesGENERAL- Additional output (A): no- Programmable relay: relay adjustable u. a. as an alarm relay or Start- / stop function for an aggregate- Protection: Output short circuit, overload, battery over-voltage, low battery voltage, over temperature, 230 V AC on inverter output to high input voltage ripple- VE. Bus Interface: For parallel and three phase operation, remote monitoring and system integrationNo: - COM port for general use- Common features: Operating Temperature Range: -20 to + 50 ° C (forced ventilation), protection class IP21- Battery connection: M8 bolts- 230 V AC outlet: spring clip- Weight: 18 kg- dimensions (HxBxT): 520 x 255 x 125 mm** Non-linear load, crest factor 3: 1

The Multiplus is a powerful inverter with a pure sinus wave, an advanced battery loader that uses adaptive charging technology, and a high-speed change voltage transfer switch in a single compactHousing. Apart from these primary functions, the Multiplus also offers several extended functions, which are explained below.Two alternating current outputs: The main exit ensures uninterrupted operation. In the event of a network failure or if the land/generator current is interrupted, the Multiplus takes over the supply of the connected consumers. Switching happens so quickly (in less than 20 milliseconds) that an interruption -free operation of computers and other electronic devices is guaranteed. The second output only provides electricity if there is an alternating current available on one of the inputs of the Multiplus AC. Consumers who are not allowed to unload the battery, such as B. a water heater can be connected to this output (a second output is only available for models with an output power of 3000 VA and more).Practically unlimited performance through parallel circuit: up to six multis can be switched in parallel with high power requirements.Three phase operation: Apart from the parallel connection, three units of the same model can also be configured for a three-phase output.PowerControl: Working with limited generator performance, limited land or network current. With the remote control panel Multi Control, the maximum network or generator current can be set. The Multiplus then takes into account other connected alternating current consumers and only uses the electricity that is still "left". This prevents the generator or the land power connection from being overloaded.Power Assist: With this function, the PowerControl principle receives a new dimension. It enables the multiplus to support too weak alternative sources. Load tips often only occur for a limited period of time. In such a case, the Multiplus ensures that too weak land electricity or generator output is immediately compensated for by energy from the battery. The load is reduced, i.e. H. If consumers are switched off, the energy that is then sufficiently existing can be used again to load the batteries.Four-stage adaptive charger and loading of two batteries: The main output using the advanced "adaptive charging" software ensures that the battery system is powerful. Another fourth stage for long periods of time in conservation mode. Apart from that, the Multiplus also loads a second battery by using an independent maintenance load output (conservation load output only available from 12 V and 24 V models). If settings have to be changed, this can be changed within of a few minutes using the new DIP switch setting process.Multi Plus- Battery voltage 12 V C 12/1600/70-16- Power Control / Power Assist: Yes- Transfer switch: 16 a-Parallel circuit and three-phase operation: Javerwichter- Input voltage area: 9.5–17 V (V DC)- Exit: output voltage: 230 V AC ± 2%, frequency: 50 Hz ± 0.1%- Kont. Output power at 25 ° C: 1600 VA **- Kont. Output power. at 25 ° C: 1300 W- Kont. Output power. at 40 ° C: 1200 W- Top performance: 3000 W- Max. Effect: 93 %- Zero-load performance: 8 W-Zero-load performance in AES mode: 5 W-Zero-load performance in search mode: 2 wladitor-AC input: Input voltage area: 187-265VAC, input frequency: 45–65 Hz / performance factor: 1- Constant charging voltage: 14.4 V DC- Conservation charging voltage: 13.8 V DC- Storage mode: 13.2 V DC- charging current house battery: 70 a- Charging current starter battery: 4 a-Battery temperature sensor: Jaall community- Additional outcome (A): No- Programmable relay: relay adjustable and a. As an alarm relay or start / stop function for an aggregate-Protection: output ceiling, overload, battery overvoltage, battery sub voltage, over temperature, 230 V AC at the inverter output, too high humming voltage at the input- Ve. Bus interface: for parallel circuits and three-phase operation, remote monitoring and system integration- Com port for general use: no- Common features: operating temperature range: -20 to +50 ° C (blower testing), protection class: IP21- Battery connection: 1.5 meter battery cable-230 V AC connection: G-St18i plug- Weight: 10 kg- Dimensions (HXBXT): 375 x 214 x 110 mm ** Nonlinear load, top factor 3: 1

The multi-Plus is a powerful inverter with pure sine wave, an advanced battery charger, which uses the adaptive charging technology, and a high-speed AC voltage transfer switch in a single compact enclosure. Apart from these primary functions, the MultiPlus offers even more advanced features that are explained below.Two AC outputs: the main output provides uninterrupted operation. In the event of a power failure or an interruption of the shore / generator power the MultiPlus takes over the supply to the connected loads. This happens so quickly (in less than 20 milliseconds) that a continuous operation is ensured of computers and other electronic devices. The second output is only supplies current when the multi-Plus AC power is available at one of the inputs. Loads that should not discharge the battery, such. be as a water heater, can be connected to this output (second output is only available in models with an output power of 3000 VA and more).Practically unlimited performance using parallel circuit: up to six MNCs can be connected in parallel at high power requirements.Three phase operation: Apart from the parallel port can also three units of the same model for a three-phase output can be configured.Power Control: Dealing with limited generator, shore side or grid power. With the Multi Control Panel can be adjusted to the maximum generator or shore power. The MultiPlus will then take account of other AC loads and uses to charge only the current that is still "left". Thus, preventing the generator or shore supply from being overloaded.Power Assist: This feature allows the power control principle on a new dimension. It allows the MultiPlus to support capacity of the alternative sources. Peak power is so often required only for a limited period. In such a case, the multi-Plus ensure that a compensating insufficient shore or generator power immediately by energy from the battery. If the load is reduced, d. H. Consumers are turned off, then back enough available energy can be used to charge the batteries.Four stage adaptive charger and two batteries: The main output makes using the advanced "adaptive charging" software for a powerful charge to the battery system software fine-tunes the automatic three-stage charging process in order to adapt it to best suit the battery status In addition, it adds.. a fourth stage added for long periods of float charging. Besides that invites the MultiPlus even a second battery by using an independent trickle charge output (trickle charge output only at 12 V and 24 V models available). If settings have to be changed, this can be within a few minutes using carried the new DIP switch setting procedure.MultiPlus - Battery voltage 12 V C 12/1200 / 50-16- Power Control / Power Assist: yes- Transfer switch: 16 A- parallel and three-phase operation: jaWECHSELRICHTER- Input voltage range: 9.5 to 17 V (VDC)- Output: Output voltage: 230 V AC ± 2% Frequency: 50 Hz ± 0.1%- cont. Output power at 25 ° C: 1200 VA **- cont. Ausgangsleistg. at 25 ° C: 1000 W- cont. Ausgangsleistg. at 40 ° C: 900 W- Peak power: 2400 W- Max. Efficiency: 93%- Zero-load power: 8 W- Zero-load power in AES mode: 5 W- Zero-load power in search mode: 2 WLADEGERÄT- AC input: Input voltage range: 187-265VAC, input frequency: 45-65 Hz / Power Factor: 1- Constant Charging Voltage: 14.4 V DC- Conservation charging voltage: 13.8 V DC- Storage mode: 13.2 V DC- Charge current house battery: 50 A- Charge current starter battery: 4 A- Battery Temperature Sensor: jaALLGEMEINES- Additional output (A): no- Programmable relay: relay adjustable u. a. as alarm relays or start / stop function for an aggregate- Protection: Output short circuit, overload, battery over-voltage, low battery voltage, over temperature, 230 V AC on inverter output to high input voltage ripple- VE. Bus Interface: For parallel and three phase operation, remote monitoring and system integrationNo: - COM port for general use- Common features: Operating Temperature Range: -20 to + 50 ° C (forced ventilation), protection class IP21- Battery Connection: 1,5 meter battery cable- 230 V AC-connection G-ST18i connector- Weight: 10 kg- dimensions (HxBxT): 375 x 214 x 110 mm ** Non-linear load, peak factor of 3: 1