Verkabelung und Installation an Bord von Yachten und Wohnmobilen

Wir bieten Ihnen eine große Auswahl an Installationsmaterial für eine sichere und normgerechte Installation der Bordelektrik. Angefangen von Kabeln und Kabeldurchführungen, über Schalter und Schaltpanele bis hin zu Sicherungen und Schutzschaltern: Unsere Ware kommt von namenhaften Herstellern und bietet hohe Qualität.

Weiterhin bieten wir Steckverbinder, Reihenklemmen und Sammelschienen, Befestigungs- und Verbindungsmaterial und natürlich die passenden Werkzeuge.

Der Versand erfolgt günstig und schnell direkt vom Großhändler.

Für ausführliche Informationen zur Planung und Ausführung der elektrischen Anlage an Bord empfehlen wir die Bootselektrik-Anleitungen in der KlabauterKiste in Kombination mit dem Buch Elektrik auf Yachten (siehe unten für Auszüge).

Expertenwissen: Zweileitersystem mit negativer Masse

Das häufigste System für die Gleichstromversorgung an Bord ist das Zweileiter-Gleichstromsystem mit negativer Masse. Dabei ist der Minuspol des Systems mit Masse oder Erde, also dem Rumpf, der Propelleranlage oder dem Schutzleiter des Wechselstromsystems verbunden. Metallische Rümpfe dürfen dabei nicht als Leiter benutzt werden. Die Absicherung der Leitungen erfolgt nur in den positiven Zweigen, Sicherungen oder Schutzschalter in den negativen Zweigen sind nicht erforderlich.

Expertenwissen: Vollständig isoliertes Zweileitersystem

In dem vollständig isolierten System – dem zweiten zugelassenen Gleichstromsystem – besteht keine Verbindung zur Schiffsmasse oder -erde. In Bezug auf Überstromsicherung werden hier die Leitungen des negativen Zweigs genauso behandelt wie die des positiven: Sie müssen abgesichert sein. Ausnahme: Die Hauptzuleitung zwischen Batterie und Verteilertafel – hier wird die negative Leitung nicht abgesichert. Die Absicherung in der Verteilertafel muss mit zweipoligen Schutzschaltern erfolgen, sodass beide Pole im Überstromfall gleichzeitig abgeschaltet werden.

Diese Infobox ist ein Auszug aus "Elektrik auf Yachten" von Michael Herrmann. Das hervorragende Fachbuch behandelt sämtliche Fragestellungen zum Thema Strom an Bord. Die aktuelle Ausgabe gibt es direkt beim Autor als E-Book (PDF).

318 in stock

H07V-K - strand tinned - 1 x 2.5 mm², red - cable

Flexible wiring line with tinned wires-H07V-like strained strands (single wirers) made of tinned copper wires, therefore extremely resistant to corrosion. Ader insulation based on PVC, can be used for installations indoors, e.g. wiring of switching boards.The problem: bare copper wires corrode very quickly. This corrosion arises wherever the copper conductor is not 100 percent airtight.The ends of the cables at the transition to cable shoe or plug are particularly at risk. The corrosion increases the resistance of the connection, increased voltage drop or functional disorders.The lines must be completely replaced, the exchange of the cables is very complex and expensive.The salty, moist or hotter the air, the faster this process is.The solution: In contrast, tinned copper wires hardly corrode and therefore have to be practically never renewed.Tinned lines are a bit more expensive, but the exchange of corroded cables is very complex, the additional price is worthwhile.Cross section 2.5 mm²Outside diameter approx. 4 mmThe prices are specified per running meter.Discount of 15 % with ≥ 100 m. The discount is automatically taken into account when determining the price.

€1.26* €1.30* (3.08% saved vs. recommended price)

326 in stock

H07V-K - strand tinned - 1 x 2.5 mm², black - cable

€1.26* €1.30* (3.08% saved vs. recommended price)

355 in stock

Cable delineates 2 x 1.5 mm², black, flexible

Tinning H05VV-VZ2x1.5mm²Ø 8 mm roundFlexible tour guide, 2-pin, with double PVC insulation. Outside coat black, vein insulation red, black.Most common installation line for yacht technology. Use indoors, e.g. as a supply line to individual consumers. Due to the wire colors, we only recommend the use for low voltage.Cross -section 2 x 1.5 mm²Outside diameter 8 mm.The prices are specified per running meter.Special prices for entire rings or roles: Discount of 10 % when decreasing ≥ 50 m. The discount is automatically taken into account when determining the price.

€2.47* €2.60* (5% saved vs. recommended price)

351 in stock

H07V -K - Litze tinned - 1 x 1.5 mm², red - cable

Flexible wiring line with tinned wires-H07V-like strained strands (single wirers) made of tinned copper wires, therefore extremely resistant to corrosion. Ader insulation based on PVC, can be used for installations indoors, e.g. wiring of switching boards.The problem: bare copper wires corrode very quickly. This corrosion arises wherever the copper conductor is not 100 percent airtight.The ends of the cables at the transition to cable shoe or plug are particularly at risk. The corrosion increases the resistance of the connection, increased voltage drop or functional disorders.The lines must be completely replaced, the exchange of the cables is very complex and expensive.The salty, moist or hotter the air, the faster this process is.The solution: In contrast, tinned copper wires hardly corrode and therefore have to be practically never renewed.Tinned lines are a bit more expensive, but the exchange of corroded cables is very complex, the additional price is worthwhile.Cross -section 1.5 mm²Outside diameter approx. 3.4 mmThe prices are specified per running meter.Discount of 15 % with ≥ 100 m. The discount is automatically taken into account when determining the price.

€1.05*

304 in stock

Flexible flat cable - 2 x 1.5 mm² (FLKK / FLYY)

Flexible flat line, 2-pin, with double PVC insulation. Outside coat black, vein insulation red, black. Most common installation line for yacht technology. Use in the interior, e.g. as a supply line to individual consumers. Due to the wire colors, we only recommend the use for low voltage.Cross section 2 x 1.5 mm², outer dimensions (BXH) 7.4 x4.2 mmThe prices are specified per running meter.Discount of 10 % with ≥ 50 m and 15 % when decreasing ≥ 100 m. The discount is automatically taken into account when determining the price.

€1.49* €1.59* (6.29% saved vs. recommended price)

195 in stock

H07V -K - Litze tinned - 1 x 1.5 mm², black - cable

Flexible wiring line with tinned wires-H07V-like strained strands (single wirers) made of tinned copper wires, therefore extremely resistant to corrosion. Ader insulation based on PVC, can be used for installations indoors, e.g. wiring of switching boards.The problem: bare copper wires corrode very quickly. This corrosion arises wherever the copper conductor is not 100 percent airtight.The ends of the cables at the transition to cable shoe or plug are particularly at risk. The corrosion increases the resistance of the connection, increased voltage drop or functional disorders.The lines must be completely replaced, the exchange of the cables is very complex and expensive.The salty, moist or hotter the air, the faster this process is.The solution: In contrast, tinned copper wires hardly corrode and therefore have to be practically never renewed.Tinned lines are a bit more expensive, but the exchange of corroded cables is very complex, the additional price is worthwhile.Cross -section 1.5 mm²Outside diameter approx. 3.4 mmThe prices are specified per running meter.Discount of 15 % with ≥ 100 m. The discount is automatically taken into account when determining the price.

€1.05*

126 in stock

Cable delineates 2 x 2.5 mm², black, flexible

tinned H05VV-VZ2x2.5mm²Ø 9mm round.Flexible round cable, 2-pole, double-PVC insulation. Outer sheath black, wire insulation red, black.Most common installation cable for Yachttechnik. Indoor use, e.g. as a supply line to individual consumers. Due to the core colors we recommend only the use of low voltage.Section 2 x 1.5 mm², mm outer diameter. 9Prices are for cuts per meter. Special rates for all rings or rolls are available. If necessary, just ask the required amount. Usually there are 25% discount for all coils.

€3.23* €3.40* (5% saved vs. recommended price)

345 in stock

Cable oil flex solar XLS-R twin 2 x 4 qmm, tinned

Radiant-networked twin solar cable;Cross -section 2x4mm²,Outside diameter 5.2x10.7mm;Double isolated 900/1500 V;Temp. Area -40 ° to +100 ° C;UV-resistant;Fine -wound;black redSpecial prices for entire rings or roles: 10% or 15% discount - 50 m or 100 m per size. The right discount is automatically taken into account when determining the price.

€4.41*

160 in stock

Cable oil flex solar XLS-R twin 2 x 2.5 qmm, tinned

Radiant-networked twin solar cable;Cross -section 2x2.5mm²,Outside diameter 4.8x9.9mm;Double isolated 900/1500 V;Temp. Area -40 ° to +100 ° C;UV-resistant;Fine -wound;black redSpecial prices for entire rings or roles: 10% or 15% discount - 50 m or 100 m per size. The right discount is automatically taken into account when determining the price.

€4.09*

473 in stock

Flexible flat cable - 2 x 1.5 mm² (FLKK / FLYY)

Flexible flat cable, 2-pole, double-PVC insulation. Outer sheath black, wire insulation red, black. Most common installation cable for Yachttechnik.Verwendung indoors, e.g. as a supply line to individual consumers. Due to the core colors we recommend only the use of low voltage.Section 2 x 0,75 mm²,Prices are for cuts per meter. Special rates for all rings or rolls are available. If necessary, just ask the required amount. Usually there are 20% or 20% or 25% (depending on the amount of 50m or 100m) (depending on the amount of 50m or 100m) discount on all coils.

€0.99* €1.10* (10% saved vs. recommended price)

573 in stock

Cable oil flex solar XLS-R twin 2 x 6 qmm, tinned

Radiant-networked twin solar cable; Cross -section 2x6mm², outside diameter 5.8x11.9mm; Double isolated 900/1500 V; Temp. Area -40 ° to +100 ° C; UV-resistant; Fine -wound; black redArticle No.: 390924Manufacturer: without a logoProduct weight: 0.17 kgWeight including packaging: 0.17 kgDimensions: 0 x 0 x 0 mm (L x W x H)Special prices for entire rings or roles: 10% or 15% discount - 50 m or 100 m per size. The right discount is automatically taken into account when determining the price.

€6.21*

100 in stock

Twin Flex - Highly flexible twin cable 2 x 6 mm² Cable

Highly flexible and soft 2-pole-pair wires with PVC double insulation, which is very easy to install.Transparent apportionable PVC outer jacket.Core insulation red, black.Suitable for all two-pole installations indoors.Low voltage on board).Section 2 x 6 mm²,The prices are per linear meter indicated. is supplied, the quantity ordered in one piece.Special rates for all rings or rolls are available. If necessary, just ask the required amount. ,

€4.80*

246 in stock

Flexible flat cable - 2 x 2.5 mm²

Flexible flat line, 2-pin, with double PVC insulation. Outside coat black, vein insulation red, black. Most common installation line for yacht technology. Use in the interior, e.g. as a supply line to individual consumers. Due to the wire colors, we only recommend the use for low voltage.Cross section 2 x 2.5 mm², outer dimensions (BXH) 8.4 x4.9 mmThe prices are specified per running meter.Discount of 10 % with ≥ 50 m and 15 % when decreasing ≥ 100 m. The discount is automatically taken into account when determining the price.

€2.25* €2.50* (10% saved vs. recommended price)

271 in stock

H07V -K - Litze tinned - 1 x 4 mm², red - cable

Flexible wiring line with tinned Drähten- H07V-KFeindrähtige strand (single-stranded) of tinned copper wires, therefore highly resistant to corrosion. Core insulation based on PVC, suitable for indoor installation, e.g. Wiring of electrical panels.Cross-section 4.0 mm, outer diameter of about 4.6 mmPrices are for cuts per meter. Special rates for all rings or rolls are available. If necessary, just ask the required amount. Usually there are 20% or 25% (depending on the amount of 50m or 100m) discount on all coils.The problem: Naked copper wires corrode very quickly. This corrosion occurs wherever the copper conductor is not sealed airtight to 100 percent. Thus, especially the ends of the cables at the transition to cable shoe or plug are compromised. Due to the corrosion resistance of the compound increases, increased voltage drop or malfunction will result. The lines must be completely replaced, the replacement of the cable is very complex and expensive. Depending salty, moist or hot air, the faster this Prozess.Die solution runs against: tinned copper wires corrode hard and must therefore be virtually nieerneuert. Tinned leads are slightly more expensive, but as the replacement of corroded cable is very expensive, the extra cost is worthwhile.

€1.89* €1.90* (0.53% saved vs. recommended price)

391 in stock

H07V-K - strand tinned - 1 x 4 mm², black - Cable

€1.89* €1.90* (0.53% saved vs. recommended price)

58 in stock

Oil flex - polyurethane coat yellow, tinned - 3 x 1.5 mm²

Flexible hose line, 3-pin, with outer coat made of polyurethane, color yellow, vein insulation made of TPE, core identification according to VDE 0293. Temperature range –40 to90 ° C. Wires made of tinned copper wires, therefore extremely resistant to corrosion. The PU coat is very resistant and abrasion -resistant, offers a high level of tensile strength and is resistant to oils, petrol and many solvents. Optimally suitable for installations outdoors or in the mast, as well as in the three -pole version also as a land connection line.Cross section 3 x 1.5 mm², diameter approx. 8.9 mmThe prices are specified per running meter.Discount of 10 % when decreasing ≥ 50 m. The discount is automatically taken into account when determining the price.

€4.83*

85 in stock

Plastic tubing, gray - 2 x 1.5 mm² cable

Flexible hose, 2-pole, with PVC outer jacket, color gray (RAL 7001) and PVC wire insulation. Core identification to VDE 0293. temperature range -5 ° C to + 70 ° C. Use on board for installation indoors. Space-saving installation due to small cable diameter. Not intended for use outdoors.Section 2 x 1.5 mm, diameter 6.3 mmPrices are for cuts per meter. Special rates for all rings or rolls are available. If necessary, just ask the required amount. Usually there are 20% or 25% (depending on the amount of 50m or 100m) discount on all coils.

€1.34*

89 in stock

Terminal block UT4

Through clamp for assembly on top sciences according to EN 50 022. Insules polyamide 6.6, fracture -proof and creep power festival.Execution of all metals: corrosion -resistant copper alloy, nickel -plated. Nominal voltage: 1000 V,Nominal current: 32 a,Connection type: screw connection,Number of connections: 2,Cross-section: 0.14 mm²-6 mm²,AWG: 26-10,Width: 6.2 mm,Color gray,Montage type: NS 35/7.5, NS 35/15Attention: Scope of delivery is 1 terminal!Any number of them can be assembled in a row on a maternaire.The picture with several terminals only serve to illustrate.

€1.60* €1.70* (5.88% saved vs. recommended price)

467 in stock

H07V-K - strand tinned - 1 x 6 mm², red - cable

Flexible wiring line with tinned Drähten- H07V-KFeindrähtige strand (single-stranded) of tinned copper wires, therefore highly resistant to corrosion. Core insulation based on PVC, suitable for indoor installation, e.g. Wiring of electrical panels.Section 6.0 mm², outer diameter of about 5.1 mmPrices are for cuts per meter. Special rates for all rings or rolls are available. If necessary, just ask the required amount. Usually there are 20% or 25% (depending on the amount of 50m or 100m) discount on all coils.The problem: Naked copper wires corrode very quickly. This corrosion occurs wherever the copper conductor is not sealed airtight to 100 percent. Thus, especially the ends of the cables at the transition to cable shoe or plug are compromised. Due to the corrosion resistance of the compound increases, increased voltage drop or malfunction will result. The lines must be completely replaced, the replacement of the cable is very complex and expensive. Depending salty, moist or hot air, the faster this Prozess.Die solution runs against: tinned copper wires corrode hard and must therefore be virtually nieerneuert. Tinned leads are slightly more expensive, but as the replacement of corroded cable is very expensive, the extra cost is worthwhile.

€2.83*

341 in stock

H07V-K - strand tinned - 1 x 6 mm, black - Cable

Flexible wiring line with tinned Drähten- H07V-KFeindrähtige strand (single-stranded) of tinned copper wires, therefore highly resistant to corrosion. Core insulation based on PVC, suitable for indoor installation, e.g. Wiring of electrical panels.Section 6.0 mm², outer diameter of about 5.1 mmPrices are for cuts per meter. Special rates for all rings or rolls are available. If necessary, just ask the required amount. Usually there are 20% or 25% (depending on the amount of 50m or 100m) discount on all coils.The problem: Naked copper wires corrode very quickly. This corrosion occurs wherever the copper conductor is not sealed airtight to 100 percent. Thus, especially the ends of the cables at the transition to cable shoe or plug are compromised. Due to the corrosion resistance of the compound increases, increased voltage drop or malfunction will result. The lines must be completely replaced, the replacement of the cable is very complex and expensive. Depending salty, moist or hot air, the faster this Prozess.Die solution runs against: tinned copper wires corrode hard and must therefore be virtually nieerneuert. Tinned leads are slightly more expensive, but as the replacement of corroded cable is very expensive, the extra cost is worthwhile.

€2.83*

129 in stock

H07V -K - Litze tinned - 1 x 10 mm², black - cable

Flexible wiring line with tinned wires-H07V-like strained strands (single wirers) made of tinned copper wires, therefore extremely resistant to corrosion. Ader insulation based on PVC, can be used for installations indoors, e.g. wiring of switching boards.The problem: bare copper wires corrode very quickly. This corrosion arises wherever the copper conductor is not 100 percent airtight.The ends of the cables at the transition to cable shoe or plug are particularly at risk. The corrosion increases the resistance of the connection, increased voltage drop or functional disorders.The lines must be completely replaced, the exchange of the cables is very complex and expensive.The salty, moist or hotter the air, the faster this process is.The solution: In contrast, tinned copper wires hardly corrode and therefore have to be practically never renewed.Tinned lines are a bit more expensive, but the exchange of corroded cables is very complex, the additional price is worthwhile.Cross -section 10.0 mm²Outside diameter approx. 6.8 mmThe prices are specified per running meter.Discount of 15 % with ≥ 100 m. The discount is automatically taken into account when determining the price.

€4.31*

131 in stock

H07V-K - strand tinned - 1 x 10 mm², red - cable

Flexible wiring line with tinned wires-H07V-like strained strands (single wirers) made of tinned copper wires, therefore extremely resistant to corrosion. Ader insulation based on PVC, can be used for installations indoors, e.g. wiring of switching boards.The problem: bare copper wires corrode very quickly. This corrosion arises wherever the copper conductor is not 100 percent airtight.The ends of the cables at the transition to cable shoe or plug are particularly at risk. The corrosion increases the resistance of the connection, increased voltage drop or functional disorders.The lines must be completely replaced, the exchange of the cables is very complex and expensive.The salty, moist or hotter the air, the faster this process is.The solution: In contrast, tinned copper wires hardly corrode and therefore have to be practically never renewed.Tinned lines are a bit more expensive, but the exchange of corroded cables is very complex, the additional price is worthwhile.Cross -section 10.0 mm²Outside diameter approx. 6.8 mmThe prices are specified per running meter.Discount of 15 % with ≥ 100 m. The discount is automatically taken into account when determining the price.

€4.31*

135 in stock

H07V-K - strand tinned - 1 x 16 mm², red - cable

Flexible wiring line with tinned wires-H07V-K Fine-wireless strands (single veins) made of tinned copper wires, therefore extremely resistant to corrosion. Ader insulation based on PVC, can be used for installations indoors, e.g. wiring of switching boards.The problem: bare copper wires corrode very quickly. This corrosion arises wherever the copper conductor is not 100 percent airtight.The ends of the cables at the transition to cable shoe or plug are particularly at risk. The corrosion increases the resistance of the connection, increased voltage drop or functional disorders.The lines must be completely replaced, the exchange of the cables is very complex and expensive.The salty, moist or hotter the air, the faster this process is.The solution: In contrast, tinned copper wires hardly corrode and therefore have to be practically never renewed.Tinned lines are a bit more expensive, but the exchange of corroded cables is very complex, the additional price is worthwhile.Cross -section 16.0 mm²Outside diameter approx. 9.0 mmThe prices are specified per running meter.Special prices for entire rings or roles: Discount of 10 % when decreasing ≥ 50 m. The discount is automatically taken into account when determining the price.

€9.02*

160 in stock

H07V-K - strand tinned - 1 x 16 mm², black - Cable

Flexible wiring line with tinned Drähten- H07V-KFeindrähtige strand (single-stranded) of tinned copper wires, therefore highly resistant to corrosion. Core insulation based on PVC, suitable for indoor installation, e.g. Wiring of electrical panels.Cross section 16.0 mm, outer diameter of about 9.0 mmPrices are for cuts per meter. Special rates for all rings or rolls are available. If necessary, just ask the required amount. Usually there are 20% or 25% (depending on the amount of 50m or 100m) discount on all coils.The problem: Naked copper wires corrode very quickly. This corrosion occurs wherever the copper conductor is not sealed airtight to 100 percent. Thus, especially the ends of the cables at the transition to cable shoe or plug are compromised. Due to the corrosion resistance of the compound increases, increased voltage drop or malfunction will result. The lines must be completely replaced, the replacement of the cable is very complex and expensive. Depending salty, moist or hot air, the faster this Prozess.Die solution runs against: tinned copper wires corrode hard and must therefore be virtually nieerneuert. Tinned leads are slightly more expensive, but as the replacement of corroded cable is very expensive, the extra cost is worthwhile.

€7.25*

Filter products

Verkabelung und Installation an Bord von Yachten und Wohnmobilen

Expertenwissen: Zweileitersystem mit negativer Masse

Expertenwissen: Vollständig isoliertes Zweileitersystem