Elektro-Innenbordmotoren von Elco

Mit diesem Device können bis zu vier Batterieblöcke parallel angeschlossen werden. Der Anschluss der Batterien erfolgt über hellblaue Andersen Stecker - die nicht Bestandteil des Lieferumfangs sind.Maße: LxBxH: 176 x 144 x 83mm

The first electric boat drive of the US manufacturer ELCO was presented at the World Exhibition in Chicago in the 1893rd 55 electric boats,equipped with ELCO drives, then transported more than 1 million visitors through the exhibition grounds.Today, more than 120 years later, produced ELCO Motor Yachts ultramodern and innovative electric drive systems, and luxury electric boats.Building on the company's history ELCO has developed a new, even more efficient range of marine power, which are based on highly reliable and virtually maintenance-free AC motors.Currently produces six different models, compared with conventional diesel engines a power range from 6 - cover 100 hp.The systems are to be installed in new and existing sailing and motor yachts, pleasure boats and light commercial vessels of from 5 to 25 meters in length, alike.The supplied with each drive system ready to install system components of the installation costs could be considerably simplified.The complete electronic engine control and monitoring is provided with a pre-assembled wiring harness and only need to be plugged together.Drive motor and control are fully integrated in a waterproof housing that can be mounted by means of lateral flanges which receive the vibration of a conventional motor base.This system makes it possible to replace existing internal combustion engines often without an elaborate reconstruction of the engine foundation.The advantages of electric drives ELCO- Proposal has no exhaust gases- Very quiet drive - no noise- Very high efficiency of 85% - 92% (a DC DC motor provides only about 55% - 60%)- Batteries are recyclable- Very low (indirect) CO² generation using solar cells or wind turbines for energy production- Take your boat every day and charge the batteries overnight for little money- The motors fit to existing mounting feet- Virtually maintenance free, no need winterizing- Available for conventional shaft systems and Saildrives- The patented motor housing prevents heat of the engine and the environment- High reliability and very long lifetime, provided maintenance after 50,000 hours of operation- When used in a hybrid system in combination with a diesel generator located approximately doubles the range compared to a conventional diesel engine.Specifications: EP-4000Recommended boat length about 32 - 48 ftSystem DC voltage 108 V DCMax. Current consumption 167 AMax electrical power 17 kW.Speed

The US manufacturer Elco's first electric boat drive was presented at the World Exhibition in Chicago in 1893. 55 electrical boats,Equipped with Elco driven, at that time transported more than 1 million visitors through the exhibition site.Today, more than 120 years later, Elco Motor Yachts produces high modern and innovative electrical drive systems and noble electroote.Building on the company history, ELCO has developed a new, even more efficient series of boat drives that are based on particularly reliable and practically maintenance -free three -phase motors.Six different models are currently being produced, which cover a power range of 6 - 100 hp compared to conventional diesel engines.The systems are equally suitable for installation in new and existing sailing and motor yachts, leisure boats and light professional shipping, from 5 to 25 meters in length.The installation effort was significantly simplified by the installed system components that are supplied with each drive system.The complete electronic engine control and monitoring is supplied with a assembled wiring harness and only have to be put together.Drive engine and regulation are completely integrated in a waterproof housing that can be assembled on a conventional engine and the vibration dampers.This system makes it possible to replace existing combustion engines in many cases without a complex conversion of the engine and the engine.The advantages of ELCO electric drives- no exhaust gases- very quiet drive - no noise pollution- Very high efficiency of 85% - 92% (a DC DC motor delivers only approx. 55% - 60%)- Batteries are recyclable- Very low (indirect) CO² production when using solar cells or wind generators for energy generation- Use your boat every day and load the batteries for little money overnight- The engines fit on existing assembly feet- practically maintenance -free, no wintering required- Available for conventional wave systems and sailDrives- The patented engine housing prevents the engine from heating up and the surroundings- High reliability and very long service life, provided maintenance after 50,000 operating hours- When using in a hybrid system in combination with a diesel generator, the range is doubled compared to a conventional diesel drive.Technical data: EP-1200Recommended boat length approx. 20 - 35 ftSystem voltage DC 48 V DCMax. Current consumption 106 aMax. Electrical power consumption 5.1 kWSpeed 1500 rpmSpeed "Power Boost" 1800 rpmComparable to a combustion engine with 12 hpLength 533 mmWidth 412 mmHeight 465 mmWeight of the engine 118 kgPerformance / ranges: (approx. Information, based on a system with AGM batteries with 245 AH capacity and a discharge depth of 50%)March ride (60% - 80% of the fuselage speed) 5 - 6.5 KTSTravel time (at 60% - 80% of the fuselage speed, approx.) 7 - 3 hours.Range (at 60% - 80% of the fuselage speed, approx.) 33 - 19 NmScope of delivery of ELCO installation electric motors:- Elco motor with integrated controller-Electronic motor display "E-Gauge IV" with Monochrome LC display- Electronic single -lever circuit for dashboard assembly- ignition lock with two keys- Controles "Power on"- Power Boost - button- Assembly InstructionsYou can find into the photos.Available options for ELCO electric motors- Motor bearing / vibration dampers-Electronic motor display E-Gauge VII with TFT color display- SailDrive (Yanmar brand)- propeller- wave couplingsThe drive systems can be supplemented with AGM or lithium batteries, accordingly dimensioned battery chargers, diesel and wind generators, solar systems and numerous installation materials from our range.We would be happy to create an offer for a complete electrical or hybrid drive system.. This article is a blocking goods. Due to the size, weight or nature of the article, there are additional shipping costs in this case, which are also calculated.

The first electric boat drive of the US manufacturer ELCO was presented at the World Exhibition in Chicago in the 1893rd 55 electric boats,equipped with ELCO drives, then transported more than 1 million visitors through the exhibition grounds.Today, more than 120 years later, produced ELCO Motor Yachts ultramodern and innovative electric drive systems, and luxury electric boats.Building on the company's history ELCO has developed a new, even more efficient range of marine power, which are based on highly reliable and virtually maintenance-free AC motors.Currently produces six different models, compared with conventional diesel engines a power range from 6 - cover 100 hp.The systems are to be installed in new and existing sailing and motor yachts, pleasure boats and light commercial vessels of from 5 to 25 meters in length, alike.The supplied with each drive system ready to install system components of the installation costs could be considerably simplified.The complete electronic engine control and monitoring is provided with a pre-assembled wiring harness and only need to be plugged together.Drive motor and control are fully integrated in a waterproof housing that can be mounted by means of lateral flanges which receive the vibration of a conventional motor base.This system makes it possible to replace existing internal combustion engines often without an elaborate reconstruction of the engine foundation.The advantages of electric drives ELCO- Proposal has no exhaust gases- Very quiet drive - no noise- Very high efficiency of 85% - 92% (a DC DC motor provides only about 55% - 60%)- Batteries are recyclable- Very low (indirect) CO² generation using solar cells or wind turbines for energy production- Take your boat every day and charge the batteries overnight for little money- The motors fit to existing mounting feet- Virtually maintenance free, no need winterizing- Available for conventional shaft systems and Saildrives- The patented motor housing prevents heat of the engine and the environment- High reliability and very long lifetime, provided maintenance after 50,000 hours of operation- When used in a hybrid system in combination with a diesel generator located approximately doubles the range compared to a conventional diesel engine.Specifications: EP-7000Recommended boat length about 38-56 ftSystem DC voltage 108 V DCMax. Current consumption 275 AMax. Electrical power consumption of 29.8 kWSpeed

The US manufacturer Elco's first electric boat drive was presented at the World Exhibition in Chicago in 1893. 55 electrical boats,Equipped with Elco driven, at that time transported more than 1 million visitors through the exhibition site.Today, more than 120 years later, Elco Motor Yachts produces high modern and innovative electrical drive systems and noble electroote.Building on the company history, ELCO has developed a new, even more efficient series of boat drives that are based on particularly reliable and practically maintenance -free three -phase motors.Six different models are currently being produced, which cover a power range of 6 - 100 hp compared to conventional diesel engines.The systems are equally suitable for installation in new and existing sailing and motor yachts, leisure boats and light professional shipping, from 5 to 25 meters in length.The installation effort was significantly simplified by the installed system components that are supplied with each drive system.The complete electronic engine control and monitoring is supplied with a assembled wiring harness and only have to be put together.Drive engine and regulation are completely integrated in a waterproof housing that can be assembled on a conventional engine and the vibration dampers.This system makes it possible to replace existing combustion engines in many cases without a complex conversion of the engine and the engine.The advantages of ELCO electric drives- no exhaust gases- very quiet drive - no noise pollution- Very high efficiency of 85% - 92% (a DC DC motor delivers only approx. 55% - 60%)- Batteries are recyclable- Very low (indirect) CO² production when using solar cells or wind generators for energy generation- Use your boat every day and load the batteries for little money overnight- The engines fit on existing assembly feet- practically maintenance -free, no wintering required- Available for conventional wave systems and sailDrives- The patented engine housing prevents the engine from heating up and the surroundings- High reliability and very long service life, provided maintenance after 50,000 operating hours- When using in a hybrid system in combination with a diesel generator, the range is doubled compared to a conventional diesel drive.Technical data: EP-1200Recommended boat length approx. 20 - 35 ftSystem voltage DC 48 V DCMax. Current consumption 106 aMax. Electrical power consumption 5.1 kWSpeed 1500 rpmSpeed "Power Boost" 1800 rpmComparable to a combustion engine with 12 hpLength 533 mmWidth 412 mmHeight 465 mmWeight of the engine 118 kgPerformance / ranges: (approx. Information, based on a system with AGM batteries with 245 AH capacity and a discharge depth of 50%)March ride (60% - 80% of the fuselage speed) 5 - 6.5 KTSTravel time (at 60% - 80% of the fuselage speed, approx.) 7 - 3 hours.Range (at 60% - 80% of the fuselage speed, approx.) 33 - 19 NmScope of delivery of ELCO installation electric motors:- Elco motor with integrated controller-Electronic motor display "E-Gauge IV" with Monochrome LC display- Electronic single -lever circuit for dashboard assembly- ignition lock with two keys- Controles "Power on"- Power Boost - button- Assembly InstructionsYou can find into the photos.Available options for ELCO electric motors- Motor bearing / vibration dampers-Electronic motor display E-Gauge VII with TFT color display- SailDrive (Yanmar brand)- propeller- wave couplingsThe drive systems can be supplemented with AGM or lithium batteries, accordingly dimensioned battery chargers, diesel and wind generators, solar systems and numerous installation materials from our range.We would be happy to create an offer for a complete electrical or hybrid drive system.. This article is a blocking goods. Due to the size, weight or nature of the article, there are additional shipping costs in this case, which are also calculated.

The first electric boat drive of the US manufacturer ELCO was presented at the World Exhibition in Chicago in the 1893rd 55 electric boats,equipped with ELCO drives, then transported more than 1 million visitors through the exhibition grounds.Today, more than 120 years later, produced ELCO Motor Yachts ultramodern and innovative electric drive systems, and luxury electric boats.Building on the company's history ELCO has developed a new, even more efficient range of marine power, which are based on highly reliable and virtually maintenance-free AC motors.Currently produces six different models, compared with conventional diesel engines a power range from 6 - cover 100 hp.The systems are to be installed in new and existing sailing and motor yachts, pleasure boats and light commercial vessels of from 5 to 25 meters in length, alike.The supplied with each drive system ready to install system components of the installation costs could be considerably simplified.The complete electronic engine control and monitoring is provided with a pre-assembled wiring harness and only need to be plugged together.Drive motor and control are fully integrated in a waterproof housing that can be mounted by means of lateral flanges which receive the vibration of a conventional motor base.This system makes it possible to replace existing internal combustion engines often without an elaborate reconstruction of the engine foundation.The advantages of electric drives ELCO- Proposal has no exhaust gases- Very quiet drive - no noise- Very high efficiency of 85% - 92% (a DC DC motor provides only about 55% - 60%)- Batteries are recyclable- Very low (indirect) CO² generation using solar cells or wind turbines for energy production- Take your boat every day and charge the batteries overnight for little money- The motors fit to existing mounting feet- Virtually maintenance free, no need winterizing- Available for conventional shaft systems and Saildrives- The patented motor housing prevents heat of the engine and the environment- High reliability and very long lifetime, provided maintenance after 50,000 hours of operation- When used in a hybrid system in combination with a diesel generator located approximately doubles the range compared to a conventional diesel engine.Specifications: EP-10000Recommended boat length about 50 - 75 ftSystem voltage DC 144 V DCMax. Current consumption 295 AMax. Electrical power consumption of 42.5 kWSpeed

The US manufacturer Elco's first electric boat drive was presented at the World Exhibition in Chicago in 1893. 55 electrical boats,Equipped with Elco driven, at that time transported more than 1 million visitors through the exhibition site.Today, more than 120 years later, Elco Motor Yachts produces high modern and innovative electrical drive systems and noble electroote.Building on the company history, ELCO has developed a new, even more efficient series of boat drives that are based on particularly reliable and practically maintenance -free three -phase motors.Six different models are currently being produced, which cover a power range of 6 - 100 hp compared to conventional diesel engines.The systems are equally suitable for installation in new and existing sailing and motor yachts, leisure boats and light professional shipping, from 5 to 25 meters in length.The installation effort was significantly simplified by the installed system components that are supplied with each drive system.The complete electronic engine control and monitoring is supplied with a assembled wiring harness and only have to be put together.Drive engine and regulation are completely integrated in a waterproof housing that can be assembled on a conventional engine and the vibration dampers.This system makes it possible to replace existing combustion engines in many cases without a complex conversion of the engine and the engine.The advantages of ELCO electric drives- no exhaust gases- very quiet drive - no noise pollution- Very high efficiency of 85% - 92% (a DC DC motor delivers only approx. 55% - 60%)- Batteries are recyclable- Very low (indirect) CO² production when using solar cells or wind generators for energy generation- Use your boat every day and load the batteries for little money overnight- The engines fit on existing assembly feet- practically maintenance -free, no wintering required- Available for conventional wave systems and sailDrives- The patented engine housing prevents the engine from heating up and the surroundings- High reliability and very long service life, provided maintenance after 50,000 operating hours- When using in a hybrid system in combination with a diesel generator, the range is doubled compared to a conventional diesel drive.Technical data: EP-600Recommended boat length approx. To 25 ftSystem voltage DC 36 V DCMax. Current consumption 70 aMax. Electrical power consumption 2.5 kWSpeed 1500 rpmSpeed "Power Boost" 1800 rpmComparable to a combustion engine with 6 hpLength 432 mmWidth 412 mmHeight 401 mmWeight of the engine 77 kgPerformance / ranges: (approx. Information, based on a system with AGM batteries with 245 AH capacity and a discharge depth of 50%)March ride (60% - 80% of the fuselage speed) 4 - 5.5 KTSTravel time (at 60% - 80% of the fuselage speed, approx.) 9 - 4 hours.Range (at 60% - 80% of the fuselage speed, approx.) 39 - 21 nmScope of delivery of ELCO installation electric motors:- Elco motor with integrated controller-Electronic motor display "E-Gauge IV" with Monochrome LC display- Electronic single -lever circuit for dashboard assembly- ignition lock with two keys- Controles "Power on"- Power Boost - button- Assembly InstructionsYou can find into the photos.Available options for ELCO electric motors- Motor bearing / vibration dampers-Electronic motor display E-Gauge VII with TFT color display- SailDrive (Yanmar brand)- propeller- wave couplingsThe drive systems can be supplemented with AGM or lithium batteries, accordingly dimensioned battery chargers, diesel and wind generators, solar systems and numerous installation materials from our range.We would be happy to create an offer for a complete electrical or hybrid drive system.Please note:When sending internal bridles / bulky goods, weight -dependent shipping costs are incurred, which we can only calculate after your order.These will be charged separately after ordering and must be paid separately. This article is a blocking goods. Due to the size, weight or nature of the article, there are additional shipping costs in this case, which are also calculated.

Surcharge for 7 "E-Gauge VII color display instead of the e-gauge IV Monochrome display contained in the scope of the e-engine.Order only possible together with an ELCO Elektro-Interborder EP-600-EP-10000!

Surcharge for 4 pieces of assembly feetOrder only possible together with an ELCO Elektro-Interborder EP-600-EP-10000!