Victron Quattro

Electricity transformer 100 A: 50 mA for multiplus-II / multigrid II for the implementation of the power controlled and power assist functions and to optimize self-consumption with external power measurement.Maximum current: 32 A.

With this device, the Victron devices can be easily programmed using the supplied software and the existing settings can be checked comfortably.Access to the device has a cable that connects the VE.Direct port on the device to the USB interface of the PC.

The digital multi-control panel GX corresponds to its predecessor, but has a new design. Another advantage of this panel lies in the simple assembly: the supplied assembly frame enables the panel to assemble both from front and from behind. The mounting holes are covered by the mounting frame. The housing of the GX panels is made of plastic. This reduces the weight of the panel and it gets a modern look. The panel is suitable for both multis and quattros. It enables the setting of PowerControl and Powerassist electricity limits for two alternating current sources: for example for generator and country power. Settings area: Up to 200 A. The brightness of the LEDs is automatically reduced during the night. Dimensions (HXBXT): 65 x 120 x 40 mm

This panel is suitable for both multinationals and for Quattro. It allows the setting of PowerControl and PowerAssist current limit setting for two AC sources, for example for a generator and shore power. Setting range: up to 200 A. The brightness of the LEDs is automatically reduced during the night.Dimensions (HxWxD): 65 x 120 x 40 mm

The Quattro is a powerful inverter with pure sine wave, an advanced battery charger, which uses the adaptive charging technology, and a high-speed AC voltage transfer switch in a single compact enclosure. Apart from these primary functions of Quattro offers even more advanced features that are explained below.Two AC outputs: the main output provides uninterrupted operation. In the event of a power failure or an interruption of the shore / generator power the Quattro takes over the supply to the connected loads. This happens so quickly (in less than 20 milliseconds) that a continuous operation is ensured of computers and other electronic devices. , The second output is live only when AC of the Quattro AC power is available at one of the entrances. Loads that should not discharge the battery, such. be as a water heater, can be connected to this output (second output is only available in models with an output power of 3000 VA and more).Practically unlimited performance using parallel circuit: up to six Quattro can be connected in parallel at high power requirements.Three phase operation: Apart from the parallel port can also three units of the same model for a three-phase output can be configured.Power Control: Dealing with limited generator, shore side or grid power. With the Multi Control Panel can be adjusted to the maximum generator or shore power. The Quattro will then take account of other AC loads and uses to charge only the current that is still "left". Thus, preventing the generator or shore supply from being overloaded.Power Assist: This feature allows the power control principle on a new dimension. It allows the Quattro support to capacity of the alternative sources. Peak power is so often required only for a limited period. In such a case, the Quattro ensure that a compensating insufficient shore or generator power immediately by energy from the battery. If the load is reduced, d. H. Consumers are turned off, then back enough available energy can be used to charge the batteries.Four stage adaptive charger and two batteries: The main output makes using the advanced "adaptive charging" software for a powerful charge to the battery system software fine-tunes the automatic three-stage charging process in order to adapt it to best suit the battery status In addition, it adds.. a fourth stage added for long periods of float charging. Besides that invites the Quattro even a second battery by using an independent trickle charge output (trickle charge output only at 12 V and 24 V models available). If settings have to be changed, this can be within a few minutes using carried the new DIP switch setting procedure.- Battery voltage 24 V: 24/3000 / 120-50 / 50- Power Control / Power Assist: yes- Transfer switch: yes- parallel and three-phase operation: yesINVERTER- Input voltage range: 19-33 V (V DC)- Output: Output voltage: 230 V AC ± 2% Frequency: 50 Hz ± 0.1%- cont. Output power at 25 ° C: 3,000 VA **- cont. Ausgangsleistg. at 25 ° C: 2,400 W- cont. Ausgangsleistg. at 40 ° C: 2,200 W- Peak power: 6000 W- Max. Efficiency: 94%- Zero-load power: 20 W- Zero-load power in AES mode: 15 W- Zero-load power in search mode: 10 WCHARGER- AC input: Input voltage range: 187-265VAC, input frequency: 45-65 Hz / Power Factor: 1- Constant Charging Voltage: 28.8 V DC- Conservation charging voltage: 27.6 DC- Storage mode: 26.4 V DC- Charge current house battery: 70 A- Battery temperature sensor: yesGENERAL- Additional output (A): yes (25 A)- Programmable relay: relay adjustable u. a. as alarm relays or start / stop function for an aggregate- Protection: Output short circuit, overload, battery over-voltage, low battery voltage, over temperature, 230 V AC on inverter output to high input voltage ripple- VE. Bus Interface: For parallel and three phase operation, remote monitoring and system integration- COM port for general use: On request- Common features: Operating Temperature Range: -20 to + 50 ° C (forced ventilation), protection class IP21- Battery Connection: four M8 bolts (2+ / 2)- 230 V AC Connection: Screw terminals 13 mm²- Weight: 19 kg- dimensions (HxBxT): 362 x 258 x 218 mm

The Quattro is a powerful inverter with pure sine wave, an advanced battery charger, which uses the adaptive charging technology, and a high-speed AC voltage transfer switch in a single compact enclosure. Apart from these primary functions of Quattro offers even more advanced features that are explained below.Two AC outputs: the main output provides uninterrupted operation. In the event of a power failure or an interruption of the shore / generator power the Quattro takes over the supply to the connected loads. This happens so quickly (in less than 20 milliseconds) that a continuous operation is ensured of computers and other electronic devices. , The second output is live only when AC of the Quattro AC power is available at one of the entrances. Loads that should not discharge the battery, such. be as a water heater, can be connected to this output (second output is only available in models with an output power of 3000 VA and more).Practically unlimited performance using parallel circuit: up to six Quattro can be connected in parallel at high power requirements.Three phase operation: Apart from the parallel port can also three units of the same model for a three-phase output can be configured.Power Control: Dealing with limited generator, shore side or grid power. With the Multi Control Panel can be adjusted to the maximum generator or shore power. The Quattro will then take account of other AC loads and uses to charge only the current that is still "left". Thus, preventing the generator or shore supply from being overloaded.Power Assist: This feature allows the power control principle on a new dimension. It allows the Quattro support to capacity of the alternative sources. Peak power is so often required only for a limited period. In such a case, the Quattro ensure that a compensating insufficient shore or generator power immediately by energy from the battery. If the load is reduced, d. H. Consumers are turned off, then back enough available energy can be used to charge the batteries.Four stage adaptive charger and two batteries: The main output makes using the advanced "adaptive charging" software for a powerful charge to the battery system software fine-tunes the automatic three-stage charging process in order to adapt it to best suit the battery status In addition, it adds.. a fourth stage added for long periods of float charging. Besides that invites the Quattro even a second battery by using an independent trickle charge output (trickle charge output only at 12 V and 24 V models available). If settings have to be changed, this can be within a few minutes using carried the new DIP switch setting procedure.- Battery voltage 12 V: 12/3000 / 120-50-50- Power Control / Power Assist: yes- Transfer switch: yes- parallel and three-phase operation: yesINVERTER- Input voltage range: 9.5 -17 V (V DC)- Output: Output voltage: 230 V AC ± 2% Frequency: 50 Hz ± 0.1%- cont. Output power at 25 ° C: 3,000 VA **- cont. Ausgangsleistg. at 25 ° C: 2,400 W- cont. Ausgangsleistg. at 40 ° C: 2,200 W- Peak power: 1000 W- Max. Efficiency: 93%- Zero-load power: 20 W- Zero-load power in AES mode: 15 W- Zero-load power in search mode: 8 WCHARGER- AC input: Input voltage range: 187-265VAC, input frequency: 45-65 Hz / Power Factor: 1- Constant Charging Voltage: 14.4 V DC- Conservation charging voltage: 13.8V DC- Storage mode: 13.2 V DC- charging current battery house: 120 A- Charge current starter battery: 4 A- Battery temperature sensor: yesGENERAL- Programmable relay: relay adjustable u. a. as alarm relays or start / stop function for an aggregate- Protection: Output short circuit, overload, battery over-voltage, low battery voltage, over temperature, 230 V AC on inverter output to high input voltage ripple- VE. Bus Interface: For parallel and three phase operation, remote monitoring and system integration- COM port for general use: On request- Common features: Operating Temperature Range: -20 to + 50 ° C (forced ventilation), protection class IP21- Battery Connection: four M8 bolts (2+ / 2)- 230 V AC Connection: Screw terminals 13 mm²- Weight: 19 kg- dimensions (HxBxT): 362 x 258 x 218 mm