Philippi P-Bus System

Battery management shunt 300AType SHX 300 with M12 connectorSimilar to picture.

AC interface in the top-hat rail for the P-BUS for measuring an AC-phase 230 V / 50 Hz.The AC interface CAV provides the following information available:- AC electrical system voltage V and AC electrical system current A- Used kilowatt hours in kWh since the last resetIn combination with an AC switching LAU possible AC power supplies are in addition, the current voltage and the active source displayed.- The electrical connection is made via screw terminals.- Following the P bus that over a one M12-T cable is included.- current measuring range (int shunt.) 16 A, 100 A (external transducer WAC)- Dimensions L 76 x W 53 x H 46 mmAVAILABLE FROM 2ND QUARTER 2017

M12 (NMEA2000) extension cable 0.5m

Connection cable length 2m

Temp-BT temperature sensor - Cable length 2,8mTemperature sensor for EM-box for battery management ShuntSHC and temperature monitor TPMType Temp-BT

M12 (NMEA 2000) T-piece

A useful article from the group NAVIGATION

M12-4T-Stück (4 fach)

P-Bus System Monitor for display, control and monitoring of all data.The PSL system is the size of the PSM 2 size and is equipped with a 5 ”color touchscreen.It provides information on all available data on various pages.A connection to an NMEA 2000 network can be established with the CBN component to be acquired. This network bridge translates the P-Bus data into the NMEA2000 network (if it supports the plotter software).- 5 “Voll colored graphics display with touchscreen-An M12-T cable and the two P-Bus Terminators (final resistance) are included in the scope of delivery- Operating voltage 8 - 32 V DC- Electricity recording max. 200 MA- Dimensions B 157.5 x H 105 x D 35 mm- Installation section B 120 x H 80 mmAvailable from the 3rd quarter of 2017

Connecting cable length 5m

DIGITAL SWITCHING AND CONTROL VIA PSM AND PSLThe new relay module enables the secure switching of 4 loads maximum 10A via the integrated fuse or circuit breaker. Potential-free switching is also possible. The respective channel can also be switched via a button via the digital switching input on the CMR.Integrated emergency operation:Each output channel can be bridged by repositioning the fuse or the automatic circuit breaker. This means that each circuit can be operated manually in the event of a system failure. The protection provided by the automatic circuit breaker or fuse is retained.Delivery incl. M12 T cable. Requires PSL from version 1.3.0 and PSM2 from version 8BCMR 411 (fuse)Switching channels: 4 (1-pole)Current load per channel: 10 A.Inputs: 4Additional function: 4 PWM dimmersDimensions: W 140 x L 120 x H 50 mm

DIGITAL SWITCHING AND CONTROL VIA PSM AND PSLThe new relay module enables the secure switching of 4 loads maximum 10A via the integrated fuse or circuit breaker. Potential-free switching is also possible. The respective channel can also be switched via a button via the digital switching input on the CMR.Integrated emergency operation:Each output channel can be bridged by repositioning the fuse or the automatic circuit breaker. This means that each circuit can be operated manually in the event of a system failure. The protection provided by the automatic circuit breaker or fuse is retained.Delivery incl. M12 T cable. Requires PSL from version 1.3.0 and PSM2 from version 8BCMR 411S (with automatic circuit breaker)Switching channels: 4 (1-pole)Current load per channel: 10 A.Inputs: 4Additional function: 4 PWM dimmersDimensions: W 140 x L 120 x H 50 mm

M12- (NMEA2000)- plug with final resistance

Digital switching and taxes via PSM and PSLThe new relay module enables a maximum of 10a to switch on 8 consumers via the integrated backup or protective switch. Potential switching is also possible. The respective channel can also be switched via the digital switching input on the CMR via a button.Integrated emergency operation:Each output channel can be bridged by passing the securing or the safety machine. This means that each circuit must be operated manually if the system fails. The coverage is retained by the safety machine or backup.Delivery including M12-T cable. PSL needs from version 1.3.0 and PSM2 from version 8bCMR 811 (fuse)Switch channels: 8 (1-pin)Electricity pollution per channel: 10 aInputs: 8Additional function: 4 PWM dimmersDimensions: W 140 x L 180 x H 50 mm

Digitaler Strommessshunt zum Einbau in die Minus-Leitung einer Ladequelle oder eines Verbrauchers. Der Anschluss der Stromversorgung erfolgt über die steckbare Klemme. Anschlussbolzen M8, P-Bus Steckverbinder M12-T. Strombelastbarkeit: 300 A, 600 A 1 min, 1500 A 0,5 sStromaufnahme: 20 mA (5 mA sleep-mode)Betriebsspannung: 8 - 32 VMeßbereich: 10 mA - 300 AAbmessungen L 118 x B 40 x H 65 mm

In order to display the data of the Xtender combi inverter and to be able to carry out the configuration settings from the PSM, the Xcom Can Bridge is required.The power supply takes place via the Xtender network.Dimensions L 113 x W 76 x H 25 mm

Connection cable length 10m

The System Monitor PSM is the central display and control element of the electrical system on board.It enables the monitoring, controlling and configuration of all Philippi P-Bus compatible components.The clearly structured user interface enables intuitive and logical operation via the touchscreen.Several system monitore PSM can be assembled side by side to present various information such as tanks, batteries, electricity balance or AC network at the same time.Alternatively, several System Monitore PSM can be installed at different positions on board in order to be able to query the desired information independently.With the system monitor PSM as a headquarters, you can always be based on the smallest expansion stage, e.g. B. with just one shunt SHC as a battery monitor, up to the function as a multifunctional display or control panel in a digitally switched CAN bus system.The 3.5 ”color touchscreen of the system monitor PSM informs you on various pages about all available data in your electrical system.In the main menu, the menu items are active, for which data is available from the connected devices.This is displayed by the colored symbol display.Possible functions, depending on the connected devices:Battery monitorIn addition to the display of electricity, voltage and capacity, the battery state is shown graphically.Information such as remaining time and statistical data are available on call.The connection of a second Shunt SHC extends the system monitor PSM to the battery monitor e.g. for starter, consumer & bug batteries.Tank monitorThe filling stands of the tanks are shown in different colors regardless of the tank sensor depending on the tank.Over- or falls below the level of an adjustable level, the respective tank appears red.The name and position of the tanks are individually adjustable.Energy monitor DCThe current loading or discharge flows of the sources and consumers are shown in the energy scheme.Alternatively, the previously loaded or consumed energy can be displayed (e.g. yield of a solar cell per season).Further specific information and control options are available in the submenu for chargers or inverters.Main switch monitorThe main battery switches can be switched at the push of a button.An optional pin code protects against unauthorized operation.The protective function when the batteries are deep discharged can be activated for the main switches.Energy monitor ACThe voltage and frequency of the connected sources, the currently feeding source and its performance data are displayed.Specific information and control options are available in the submenu for generators and inverter.Consumer controlSwitching consumers in a digital bus system enables comfortable operation of one or more places.In conjunction with LED lamps and the interface CMR, a trouble -free dimming function of the lamps is available.- 3.5 “full-colored graphics display with touchscreen.-An M12-T cable and the two P-Bus Terminators (final resistance) are included.- Operating voltage 8 - 60 V DC- Power consumption 100 mA, stand-by: 6 mA- Dimensions L 105 x W 105 x D 35 mm- Installation section 88 x 88 mm

DIGITALES SCHALTEN UND STEUERN ÜBER PSM UND PSL2 Schalkanäle (2-polig)Strombelastung je Kanal 30AAbsicherung mit Sicherungsautomaten2 EingängeAbmessungen B 140 x L 180 x H 50 mmÜber die Systemmonitore PSM und PSL können verschiedene Steuerfunktionen (siehe unten) visualisiert und Verbraucher geschaltet werden. Am Monitor PSM bzw. PSL wird der Schaltzustand bzw. die defekte Sicherung am Ausgang angezeigt. Die neuen Relaismodule ermöglichen das abgesichterte Schalten von Verbrauchern über die integrierte Sicherung bzw. Schutzschalter. Potentialfreies Schalten ist ebenfalls möglich. Über den digitalen Schalteingang am CMR kann zusätzlich über einen Taster der jeweilige Kanal geschaltet werden. Die Relaismodule sind als ein- bzw. zweipolige Version verfügbar. Integrierter Notbetrieb: Jeder Ausgangskanal kann durch Umstecken der Sicherung bzw. des Sicherungsautomaten überbrückt werden. Somit ist jeder Stromkreis bei einem Ausfall der Anlage manuell zu bedienen. Dabei bleibt die Absicherung durch den Sicherungsautomaten bzw. Sicherung erhalten. Neue zusätzliche Funktionen:1) Main/Secondary Jeder Schaltkanal kann einem zweiten Schaltkanal zugeordnet werden. Damit können mit einen Schaltbefehl mehrere Ausgänge gleichzeitig geschaltet werden. Z. B. für Notfunktionen (Panikschalter schaltet alle Lampen ein) oder für Szenarienschalter. 2) Freigabefunktion Der Ausgang wird erst geschaltet wenn am Steuereingang ein Taster betä_x0002_tigt wird. Damit können z.B. am Monitor alle Beleuchtungskreise zentral freigeben werden und lokal in den Kabinen geschaltet werden. Somit kön_x0002_nen alle Lampen zentral ausgeschaltet werden. Es können pro Kanal meh_x0002_rere Taster parallel angeschlossen werden, um von mehreren Stellen aus das Licht ein und auszuschalten (Stromstoßschalter-Funktion). 3) Meldefunktion Die Meldungsfunktion ermöglicht die Visualisierung von Zuständen und Ereignissen auf dem Monitor und einer entsprechenden Warnmeldung Mittels den 4 Steuerkanälen (PWM) können LED-Leuchten oder LED_x0002_Leistungstreiber mit Steuereingang zum Dimmen (z.B. Prebit - Secondary Leuchten) vom Monitor PSM / PSL aus gesteuert werden.

DIGITALES SCHALTEN UND STEUERN ÜBER PSM UND PSL4 Schalkanäle (1-polig)Strombelastung je Kanal 30AAbsicherung mit ATO Sicherung4 EingängeAbmessungen B 140 x L 180 x H 50 mmÜber die Systemmonitore PSM und PSL können verschiedene Steuerfunktionen (siehe unten) visualisiert und Verbraucher geschaltet werden. Am Monitor PSM bzw. PSL wird der Schaltzustand bzw. die defekte Sicherung am Ausgang angezeigt. Die neuen Relaismodule ermöglichen das abgesichterte Schalten von Verbrauchern über die integrierte Sicherung bzw. Schutzschalter. Potentialfreies Schalten ist ebenfalls möglich. Über den digitalen Schalteingang am CMR kann zusätzlich über einen Taster der jeweilige Kanal geschaltet werden. Die Relaismodule sind als ein- bzw. zweipolige Version verfügbar. Integrierter Notbetrieb: Jeder Ausgangskanal kann durch Umstecken der Sicherung bzw. des Sicherungsautomaten überbrückt werden. Somit ist jeder Stromkreis bei einem Ausfall der Anlage manuell zu bedienen. Dabei bleibt die Absicherung durch den Sicherungsautomaten bzw. Sicherung erhalten. Neue zusätzliche Funktionen:1) Main/Secondary Jeder Schaltkanal kann einem zweiten Schaltkanal zugeordnet werden. Damit können mit einen Schaltbefehl mehrere Ausgänge gleichzeitig geschaltet werden. Z. B. für Notfunktionen (Panikschalter schaltet alle Lampen ein) oder für Szenarienschalter. 2) Freigabefunktion Der Ausgang wird erst geschaltet wenn am Steuereingang ein Taster betä_x0002_tigt wird. Damit können z.B. am Monitor alle Beleuchtungskreise zentral freigeben werden und lokal in den Kabinen geschaltet werden. Somit kön_x0002_nen alle Lampen zentral ausgeschaltet werden. Es können pro Kanal meh_x0002_rere Taster parallel angeschlossen werden, um von mehreren Stellen aus das Licht ein und auszuschalten (Stromstoßschalter-Funktion). 3) Meldefunktion Die Meldungsfunktion ermöglicht die Visualisierung von Zuständen und Ereignissen auf dem Monitor und einer entsprechenden Warnmeldung Mittels den 4 Steuerkanälen (PWM) können LED-Leuchten oder LED_x0002_Leistungstreiber mit Steuereingang zum Dimmen (z.B. Prebit - Secondary Leuchten) vom Monitor PSM / PSL aus gesteuert werden.

In order to be able to output the battery, tank and other P-bus data of the PSM monitor on card ploters and NMEA2000® compatible devices, an NMEA 2000® Bridge is necessary, which convert the data accordingly.The following PGNs are supported: 127501, 127505, 127506, 127508, 127744, 127747, 127750.Please check which PGNs can currently be presented by your plotter, as this depends on the manufacturer and software stand.The power supply takes place via the NMEA2000® network.Dimensions L 107 x W 85 x H 40 mm

In order to display the data of the combination inverter and lithium batteries from Mastervolt at the PSM and to be able to make the settings, the CMB Bridge is required.The power supply takes place via the master bus network.Dimensions H 66 x W 78 x D 32 mmAvailable from the 2nd quarter of 2017

Digital switching and taxes via PSM and PSL4 formwork channels (2-pin)Electricity pollution per channel 10aProtection with safety machines4 inputs4 PWM dimmersDimensions B 140 x L 180 x H 50 mmVarious control functions (see below) can be visualized and consumers switched via the system monitors PSM and PSL.The switching status or the defective backup at the output is displayed on the monitor PSM or PSL.The new relay modules enable the defined switching of consumers via the integrated backup or circuit breaker.Potential switching is also possible.The respective channel can also be switched via the digital switching input on the CMR via a button.The relay modules are available as one or two-pole version.Integrated emergency operation:Each output channel can be bridged by passing the securing or the safety machine.This means that each circuit must be operated manually if the system fails.The coverage is retained by the safety machine or backup.New additional functions:1) Main/SecondaryEach switching channel can be assigned to a second switch channel.This means that several outputs can be switched at the same time with a switching command.For example, for emergency functions (panic switches switches on all lamps) or for scenario switches.2) Release functionThe output is only switched when a button is attached to the control entrance.For example, all lighting circles can be released centrally on the monitor and switched locally in the cabins.Thus, all lamps can be switched off centrally.The light can be connected in parallel per channel in order to switch on and off the light from several places (power switch function).3) Registration functionThe message function enables the visualization of states and events on the monitor and a corresponding warning message using the 4 control channels (PWM) LED lights or LED performance drivers with a control receipt for dimming (e.g. Prebit - Secondary lights) can be controlled from the Monitor PSM / PSL .

Digital switching and taxes via PSM and PSL2 formwork channels (2-pin)Electricity load per channel 30AProtection with ATO fuse2 inputsDimensions B 140 x L 180 x H 50 mmVarious control functions (see below) can be visualized and consumers switched via the system monitors PSM and PSL.The switching status or the defective backup at the output is displayed on the monitor PSM or PSL.The new relay modules enable the defined switching of consumers via the integrated backup or circuit breaker.Potential switching is also possible.The respective channel can also be switched via the digital switching input on the CMR via a button.The relay modules are available as one or two-pole version.Integrated emergency operation:Each output channel can be bridged by passing the securing or the safety machine.This means that each circuit must be operated manually if the system fails.The coverage is retained by the safety machine or backup.New additional functions:1) Main/SecondaryEach switching channel can be assigned to a second switch channel.This means that several outputs can be switched at the same time with a switching command.For example, for emergency functions (panic switches switches on all lamps) or for scenario switches.2) Release functionThe output is only switched when a button is attached to the control entrance.For example, all lighting circles can be released centrally on the monitor and switched locally in the cabins.Thus, all lamps can be switched off centrally.The light can be connected in parallel per channel in order to switch on and off the light from several places (power switch function).3) Registration functionThe message function enables the visualization of states and events on the monitor and a corresponding warning message using the 4 control channels (PWM) LED lights or LED performance drivers with a control receipt for dimming (e.g. Prebit - Secondary lights) can be controlled from the Monitor PSM / PSL .