Batteriemonitore von Philippi

The delivery takes place including Shunt She 300The BLS battery monitor is a compact battery monitoring for battery systems consisting of a 12 V starter battery and one or more 12 V consumer battery (s).The 2.4 “TFT Touch screen shows all important data of the entire battery system at a glance without having to operate a button.The built -in brightness sensor automatically dims the screen in the dark and saves valuable energy.• Display of the current voltage, the current charging or discharge current, the remaining remaining time, the battery temperature and the loading status of the consumer battery (s).• Further information on the use of the consumer battery (s): Number of charging cycles, deep discharges and the medium discharge depth.• Warning of a dangerous deep discharge through an adjustable acoustic alarm.• Suitable for all battery types such as acid, gel, AGM and LIFEPO4easy installationThe connection between the monitor and the shunt consists of a single line, an existing line can also be used.Easy commissioningOnly the battery capacity of the consumer battery has to be entered and the system is ready for use.Easy handlingBecause all relevant information is summarized on one page, no button has to be pressed. The important information is presented in an understandable manner and enable the quick reading.Technical specificationsNominal voltage 12 VElectricity recording max. 50 MA @ 12V, stand-by: 6 mADimensions W 105 x H 75 x D 35 mmInstallation section 87 x 65 mmElectricity resilience Shunt 300A, 600 A 1min, 1500 A 0.5 sExpand the BLS monitor by connecting a charger of the ACE series to a full battery charging management systemThe interface ACE-LIN interface integrated in the automatic loader enables the BLS battery monitor to monitor and control the charging process of the ACE ACE automatic loader to optimize the load.The AC network voltage, the loading phase, the battery temperature, the charging voltage and the charging current can also be read on the display.The charging capacity can be reduced at the push of a button or the silent mode (fan-off) can be activated. For further charging monitoring, a temperature alarm can be defined, for example.

Digital battery Management Shunt for installation in the minus line of the consumer battery.The Shunt She 348 is compatible with the monitor BTM2, BLM2 and BLS.The SHUTS power is supplied via the voltage measurement line of the consumer battery.Suitable for permanent charging or discharge flows up to 300 A and battery capacities up to 1000 AH.The active Shunt She 348 captures all loading and consumer flows directly on the shunt and, with the inclusion of the tension, calculates the current charging status of the battery.• High measuring accuracy of 10 mA• Large measuring range from 0.01 a to 1500 a• Automatic battery recognition• determination of the state of charge• Measurement of the battery temperature of the consumer battery via the optional temperature sensor "Temp-BT"• Tension measurement of a second battery group (starter battery)Electricity load capacity 300A, 600 A 1min, 1500 A 0.5 sElectricity recording 10 MA@12 V, 5 MA@24 VOperating voltage DC 8-40 VMeasure area 10 MA - 1500 aConnection bolt M8Dimensions L 118 x W 40 x H 65 mm

All information about the battery system at a glance and - if needed - on your card plotter about the NMEA2000/SEATALK NG interface.Monitoring of the abdomen and starter battery via the Shunt She 348 (included in the scope of delivery).n The performance and energy yield of a solar system can be read by means of an additional shunt SHP 300.n For the connection to an NMEA 2000 or Raymarine network, the N2K cable with M12 plug and an additional adapter is required for Raymarine.Intuitive, 3.5 “color-TFT-touchscreen graphics display with brightness sensor for automatic adjustment of display brightness. Including NMEA 2000 interface (accessories N2K cable).Apprenticeship options:Additional measurement of an energy source (solar etc.) via Shunt SHP.Battery management via remote -controllable main switch FBR 265.Operating voltage 8 - 64 VElectricity recording max. 70 MA @ 12V, stand-by: 6 mADimensions L 105 x W 105 x H 35 mmInstallation section 88 x 88 mm

Two-stage discharge protection for optimum protection of your batteriesDischarge 12 / 24V with alarm, Type TSD 40The remote-controlled discharge TSD 40 protects the battery (ies) from damage by deep discharge.Conventional devices switch to a shock loads connected from.With the two-stage discharge, you can continue to operate important or safety-relevant consumers, while luxury is disconnected if declining battery voltage in a first step.Of the impending shutdown warns an audible alarm.The restart occurs automatically at 12.5 / 25V.The setting "13 V" an energy management can be realized, e.g.. an additional cooler, a heating mat or a water heater can be activated as soon as the generator is running or a solar panel generates enough energy.With the remote control panel FB-TSA, the two outputs can be remotely switched and turned back on in an emergency for a short period of time.Operating voltage 12/24 V DC, set via DIP switchesSwitching capacity per channel (2) max. 40 ACut-off voltage Rel.1 * via DIP switches: 11.8 / 12.0 / 12.2 / 13 V @ 300 sShutdown voltage Rel.2 * via DIP switches: 10.8 / 11.2 V @ 50 sReclosing voltage * 12.5VCurrent consumption of 1,3 mA / 12 V, 2 mA / 24 VConnection screw terminals, max. 10 mm2Dimensions L 130 x W 80 x H 42 mm* At 24V: duplicate values!

Control panel 40 for the discharge TSD Using the control panel can be switched consumers (to 40A) on the TSD 40 (ON / OFF). The control LED indicates the operating state.not suitable for TSA 265!Dimensions W x H 105 52.5 x 40 mm T

Supplied without shuntThe integrated into the automatic loader interface ACE-LIN enables the battery monitor BLS to monitor and control the charging operation of the automatic loader ACE to optimize the charge.in addition, the AC line voltage, the charging phase, the battery temperature, the charging voltage and charging current can be read on the display.Pressing a button reduces the charging power or the silent mode (fan-out) enabled. To further charge monitoring can e.g. a temperature alarm can be defined.2.4 "TFT touch remote display panel for the Chargers, the ACE series.For the Chargers ACE 12/60 and 24/30 no interface ACE LIN is necessary.be ordered to be inserted into the charger ACE for the Chargers ACE 12/25, 12/40 and 24/20 must Interface ACE LIN.With the addition of a shunt (SHE 300) of the BLS can be erweiteret to a full battery monitor.Dimensions W x H 105 x D 75 40 mm

The further development of the proven battery tank monitor BTM includes an integrated NMEA2000 interface that provides the battery and tank data to the NMEA2000 network.This enables the battery and tank data to be displayed on compatible ploters.The operation at 12 - 48 V DC operating voltage is also new, so 48 V battery systems can also be monitored in conjunction with the Shunt SHE 348.The N2K cable is also required to connect to the NMEA2000 network. The plug-in cable establishes the connection via a T-piece (5 0411 1149) to an NMEA 2000 on-board network or a raymarine network (adapter cable Seatalk/NMEA 2000 A06045).Intuitive, 3.5 “color-TFT touchscreen graphic display with brightness sensor for automatic adjustment of theDisplay brightness.Including NMEA 2000 interfaceThe tank sensors, the shunt, the charger interface "ACE-Lin" and the NMEA 2000 connection cable "N2K cable" must be ordered separately.Operating voltage 8 - 64 VElectricity recording max. 70 MA @ 12V, stand-by: 6 mADimensions L 105 x W 105 x H 35 mmInstallation section 88 x 88 mm

Motor vehicle relay for general application or as a battery separating relay for small battery systems.Spool 1.8 WSwitching current: 50 (70) A or 40 A at Rel 4012 VConnection flat connector 9.6 mm / 6.3 mmDimensions B 32 x L 29 x H 59 mm coil: 24 V / 1.8 WSwitching current: 50 (70) aConnection / Th>: flat connector 9.6 mm / 6.3 mmDimensions (W x L x D): 32 x 29 x 59 mm

Distance display for chargersACE 12/25ACE 12/40ACE 24/20SET includes panel, interfaclate for inserting into the ACE and 5M connecting cableDimensions W 105 x H 52.5 x D 40 mm

zur Überwachung einzelner Ladequellen oder Verbraucher.Mit dem zusätzlichen Shunt kann z.B. die Leistung und der Energieertrag einer Solaranlage abgelesen werden. Geeignet für die Monitore BTM2, BLM2, VTM2 und LTM2Geliefert wird je nach Herstellerverfügbarkeit SHP 348 oder SHP 300. Beide Varianten sind für 12-und 24-Volt Systeme geeignet. Nur bei 48-Volt-Systemen ist der SHE 348 zwingend erforderlich!

-12 circuits with thermal protective switches 8 A, luminaire display, rocker switch, battery tank monitor TCS (2x voltage, 3x fuel indicator)- Dimensions W 220 x H 145 x D 70 mm- recommended series terminals type RKL 16/4The circuit distributors of the 100 series are equipped with thermal security machines of the E-T-A 1140 series.Each individual circuit consists of a thermal safety machine, an LED control light and a rocker switch.In the short -circuit case, the red button of the thermal safety machine jumps out and the control light goes out.By pressing the red button, the circuit can be put back into operation after removing the error.8 A types are used at the factory, but on request 4 A, 6 A, 8 A, 10 A, 12 A or 16 A safety machines can also be used.The dimensions of the panels are coordinated, so that several panels can be added vertically and horizontally.The compact digital 2.4 “touchscreen monitor PDM is designed for battery and tank monitoring on small and medium-sized systems.The starter and consumer battery can be monitored in voltage.There are 3 entrances available for the tank level measurement.Only one fuel provider TGT / TGW can be connected to tank1.Tank 2 and 3 can be connected directly to tank 2 and 3 TGT / TGW or UTV,The supplier TDS after a hardware modification.

The tank interface TIL adapts the signals of two fresh water tufts probes to the battery-tank monitor BTM.Operating voltage 10 - 30 V DCCurrent consumption 10 mADimensions W x H 130 x D 80 42 mm

The lithium battery tank monitor LTM builds on the well-known battery tank monitor BTM and is expanded to include a data interface that represents the data of one or more lithium battery (s) of the LB series.n The current display of the lithium battery LB can be improved from 1A to up to 10 mA via an additional shunt she.n Using an additional shunt SHP, the performance and the energy yield can be read for e.g. a solar system.Intuitive, 3.5 “Color-Tft touchscreen graphic display with brightness sensor for automatic adjustment of the display brightness.The tank sensors, the optional Shunts She and SHP and the “ACE-LIN” interface charger must be ordered separately.Operating voltage 8 - 64 VElectricity recording max. 60 MA @ 13V, stand-by: 6 MADimensions L 105 x W 105 x H 35 mmInstallation section 88 x 88 mm

Mass collecting rail type SAS 4

With the help of the tax interface TSR, the remote -controllable battery switch circuit bruese ML (BS7702 - 500A continuous output) can also be used as deep discharge protection.Manual emergency control on the relay is possible.- Nominal voltage 24 V DC- Section voltage 22.4 V @300 S- re -hinting voltage 25 V- overvoltage shutdown 31.2 V @60 s- Self -electricity consumption 1.3 mA- Dimensions L 120 x W 110 x H 50 mm

- 3.5 “full-colored graphics display with touchscreen.-An M12-T cable and the two P-Bus Terminators (final resistance) are included.- Operating voltage 8 - 60 V DC- Power consumption 100 mA, stand-by: 6 mA- Dimensions L 105 x W 105 x D 35 mm- Installation section 88 x 88 mm

With the help of the tax interface TSR, the remote -controllable battery operator Bluesea ML (BS7700 - 500A continuous output) can also be used as deep discharge protection.Manual emergency control on the relay is possible.- Nominal voltage 12 V DC- Section voltage 11.2 V @300 S- re -hinting voltage 12.5 V- overvoltage shutdown 15.6 V @60 s- Self -electricity consumption 1.3 mA- Dimensions L 120 x W 110 x H 50 mm