According to CE-Richtilinien, the state protection manager must be connected to the negative direct current of your yacht.This means that the saildrive, engine, valves and much more are almost automatically connected to the land protection manager. Due to the connection between the protective conductor and the negative direct current, there can be a galvanic balance between the neighboring yacht, the marina or other buildings in the water and its yacht.If your ship is protected with anodes, these are used up. The installation of a galvanic insulator reduces zinc consumption.The insulator is connected between the land connection and 230 V electrical system.Maximum electricity 16 A.Housing made of anodized aluminum, waterproof in epoxy, protection class IP 67.Weight 1 kg, dimensions (LXBXH): 200 x 120 x 60 mm.

Built-in Bluetooth Smart: No dongle neededThe wireless solution for set-up, monitoring and updating of the controller using Apple and Android smart phones, tablets or other devices.VE.DirectFor a wired data connection with a Color Control Panel, a PC or other devices.Ultra fast Maximum Power Point Tracking (MPPT)Especially in overcast sky, when the light intensity is constantly changing, improves an extremely fast MPPTRegler the energy yield compared to PWM charge controllers by up to 30% and in comparison to slower MPPT controllers by up to 10%.load outputOvercharging of the battery can be prevented by all loads are connected to the load output.The load output disconnects the loads when the battery has been up to a predetermined voltage value discharged.Alternatively, can also choose an algorithm for intelligent battery management: See Battery Life.The load output is short-circuit proof.Battery Life: intelligent battery managementIf the solar charging controller is not able to charge the battery within one day up to its full capacity, the status of the battery changes constantly "partially loaded" and between "the end of discharge" back and forth.This mode of operation (no regular full charging) damaged a lead-acid battery within a few weeks or months.The Battery Life algorithm monitors the state of charge of the battery and, if necessary he lifts every day the threshold value for separating the load on (i. E., The load is disconnected earlier) until the recovered energy sufficient to charge the battery up to almost 100%. From this point, the threshold value is modulated for the disconnection of the load, so that the charging nearly 100% is achieved about once weekly.Programmable battery charging algorithmFor more information, see the section Software on the Victron Energy website.Day / night time control and light insulation optionFor more information, see the section Software on the Victron Energy website.Options for programming, real-time data and display the course- Modern Apple and Android smartphones, tablets, Macbooks and other devices- Color Control PanelBattery voltage: 12/24 V automatic selectionNominal charging current: 15 ANominal PV power, 12 V 1a, b): 220WNominal PV power, 24V 1a, b): 440WMax. Short-circuit current of the solar system 2): 15AAutomatic load disconnect Yes, maximum load 15AMaximum PV open voltage: 75VPeak efficiency: 98%Power consumption 12V: 25 mA 24 V: 15 mA"Constant" -Ladespannung (absorption): 14.4V / 28.8 V (regulated)"Conservation" -Ladespannung (float): 13.8V / 27.6V (adjustable)Charging algorithm: multi-level, adaptiveTemperature Compensation: -16 mV / ° C and -32 mV / ° CUninterrupted / load current: 15 A 20 ASwitching off the load at a low voltage: 11.1 V / V 22.2 and 11.8 V / V or 23.6 Battery Life algorithmReconnecting the load to a low voltage: 13.1 V / 26.2 V or 14 V / 28 V or Battery Life algorithmProtection: reverse polarity of battery (backup) / Output short circuit / over-temperatureOperating Temperature: -30 ° C to +60 ° C (full rated output up to 40 ° C)Humidity: 95% non-condensingData communication port: VE.DirectConnections: 6 mm² / AWG10Protection class IP43 (electronic components), IP22 (connection area)Weight: 0.5 kgDimensions: (HxBxT) 100 x 113 x 40 mm1a) If more PV power is connected, the controller limits the input power1b) The PV voltage must reach at least the height of Vbat + 5 V, so that the controller receives the operation.After that, the minimum value of the PV voltage at Vbat + 1 V. is2) A higher short-circuit current can damage the regulator in the event of a reverse polarity connection of the PV system.

With Ethernet connection.A maximum of 65a/phase.

Victron installation accessories

Victron installation accessories

The CYRIX-CT battery connection relay replaced isolators.The main advantage is that virtually no voltage loss occurs and thus eliminates the need for a voltage increase in alternator or battery charger.Normally, the alternator is directly connected to the starter battery.The other batteries for the electrical system, the thruster, or other bodies to be respectively switched separately via Cyrix CT.Only when the starter battery has reached the preset voltage, the parallel charging of the other batteries.Bidirectional voltage sensing and voltage supply through all batteries Cyrix CT detects the voltage of all connected batteries.So the charging voltage is detected a possibly connected charger of the system battery and considered.Cyrix CT can be switched to a plurality of batteries in parallel operation in an emergency by a pressure switch (30 sec operating time) or a manually operated switch.This is particularly advantageous when e.g. the starter battery is empty or damaged.Cyrix CT is suitable for 12 volts and 24 volt vehicle electrical systems and automatically detects the system voltage.LED status indicator: NoConstant current: 120 ANominal value starting current (5 Sec.): 180 AConnecting voltage: from 13 V to 13.8 V and 26 to 27.6 with intelligent identification of trendsVoltage interrupt: from 11 V to 12.8 V and 22 to 25.7 V with intelligent identification of trendsCurrent consumption when open: <4 mACurrent consumption when closed: 12 V: 220 mA 24 V: 120 mAStart Assist Yes (Cyrix remains 30 seconds operating)Control cable included (length: 1 m): No.Protection: IP54Weight kg (lbs): 0.11 (00:24)Dimensions HxBxT in mm: 46 x 46 x 80

Temperature sensor, suitable for many Victron combination devices and chargers, e.g. Quattro, Multiplus, Phoenix, etc.

Built-in Bluetooth Smart: No dongle neededThe wireless solution for set-up, monitoring and updating of the controller using Apple and Android smart phones, tablets or other devices.VE.DirectFor a wired data connection with a Color Control Panel, a PC or other devices.Ultra fast Maximum Power Point Tracking (MPPT)Especially in overcast sky, when the light intensity is constantly changing, improves an extremely fast MPPTRegler the energy yield compared to PWM charge controllers by up to 30% and in comparison to slower MPPT controllers by up to 10%.load outputOvercharging of the battery can be prevented by all loads are connected to the load output.The load output disconnects the loads when the battery has been up to a predetermined voltage value discharged.Alternatively, can also choose an algorithm for intelligent battery management: See Battery Life.The load output is short-circuit proof.Battery Life: intelligent battery managementIf the solar charging controller is not able to charge the battery within one day up to its full capacity, the status of the battery changes constantly "partially loaded" and between "the end of discharge" back and forth.This mode of operation (no regular full charging) damaged a lead-acid battery within a few weeks or months.The Battery Life algorithm monitors the state of charge of the battery and, if necessary he lifts every day the threshold value for separating the load on (i. E., The load is disconnected earlier) until the recovered energy sufficient to charge the battery up to almost 100%. From this point, the threshold value is modulated for the disconnection of the load, so that the charging nearly 100% is achieved about once weekly.Programmable battery charging algorithmFor more information, see the section Software on the Victron Energy website.Day / night time control and light insulation optionFor more information, see the section Software on the Victron Energy website.Options for programming, real-time data and display the course- Modern Apple and Android smartphones, tablets, Macbooks and other devices- Color Control PanelBattery voltage: 12/24 V automatic selectionNominal charging current: 10 ANominal PV power, 12 V 1a, b): 145WNominal PV power, 24V 1a, b): 290W 4Max. Short-circuit current of the solar system 2): 13AAutomatic load disconnect Yes, maximum load 15AMaximum PV open voltage: 75VPeak efficiency: 98%Power consumption 12V: 25 mA 24 V: 15 mA"Constant" -Ladespannung (absorption): 14.4V / 28.8 V (regulated)"Conservation" -Ladespannung (float): 13.8V / 27.6V (adjustable)Charging algorithm: multi-level, adaptiveTemperature Compensation: -16 mV / ° C and -32 mV / ° CUninterrupted / load current: 15 A 20 ASwitching off the load at a low voltage: 11.1 V / V 22.2 and 11.8 V / V or 23.6 Battery Life algorithmReconnecting the load to a low voltage: 13.1 V / 26.2 V or 14 V / 28 V or Battery Life algorithmProtection: reverse polarity of battery (backup) / Output short circuit / over-temperatureOperating Temperature: -30 ° C to +60 ° C (full rated output up to 40 ° C)Humidity: 95% non-condensingData communication port: VE.DirectConnections: 6 mm² / AWG10Protection class IP43 (electronic components), IP22 (connection area)Weight: 0.5 kgDimensions: (HxBxT) 100 x 113 x 40 mm1a) If more PV power is connected, the controller limits the input power1b) The PV voltage must reach at least the height of Vbat + 5 V, so that the controller receives the operation.After that, the minimum value of the PV voltage at Vbat + 1 V. is2) A higher short-circuit current can damage the regulator in the event of a reverse polarity connection of the PV system.

Remote monitoring panels &

Victron installation accessories

Smart charger Blue - 12V, 15A, 1 outputBluetooth SmartThe Blue Smart IP22 battery charger is the wireless solution for monitoring voltage and current, to customizeSettings and to update the charger when new features are available.High efficiencyWith an efficiency of up to 94% these chargers produce compared to the industry standard up to four times less heat.After the battery has also been fully charged, the power consumption drops to less than 0.5 Watts, which is about five toten times better than the industry standard.Adaptive 6-stage charging algorithm: Test Bulk - Absorption - Recondition - Float - StorgageThe Blue smart charger features a battery management through its microprocessor controlled "adaptive". "Adaptive"that charging automatically the type of battery usage is adjusted.Overlay mode: Less maintenance and aging in the idle state of the battery:The overlay mode will be activated if no discharge has taken place within 24 hours. TheFloat voltage is then lowered to 2.2V / cell (13.2 V for a 12 V battery), in order to minimize the evolution of gas andto prevent corrosion of the positive plates. Once a week the voltage is raised to the level of gassing.This achieves a kind of compensation charge that the electrolyte stratification and sulfation - the two main reasons for prematureBattery failure - prevented.Loading and lithium-ion (LiFePO4) batteriesLiFePO4 batteries with a simple constant current phase - constant voltage phase - float voltage phaseAlgorithm loaded.The settings NIGHT and LOWthe device is in mode or NIGHT is LOW, the output current is reduced to a maximum of 50% of the rated output and theCharger works absolutely silent. The NIGHT mode ends automatically after 8 hours. The LOW mode can be manually stop.Protection against overheatingThe output current is reduced when the temperature rises to up to 50 ° C, however, the Blue Smart charger not failed.Elf status indicator LEDsCharging algorithm: TEST / BULK (bulk phase) / Absorption (constant voltage phase / RECONDITION (REGENERATE) /FLOAT (float charge PHASE) / STORAGE (STORAGE MODE) / READY (READY)Settings of MODE: NORMAL (14.4V) / HIGH (HIGH) (14.7V) / RECONDITION (REGENERIENE) / LI-ION Input voltage range: 180 - 265 VAC Charging current, normal mode: 15A Charging current, or NIGHT LOW: 7.5A Efficiency: 93% Power consumption without load: 0.5 W Frequency: 45 - 65 Hz Number of Outputs: 1 'Konstant' charging voltage: Normal: 14.4V High: 14.7V Li-ion: 14.2V 'Erhaltungs' charging voltage: Normal: 13.8V High: 13.8V Li-ion: 13.5V 'Lagerungs'-charge voltage (Storage): Normal: high 13.2 V: 13.2 V Li-ion: 13.5V Charging Algorithm: sechsstufig adaptively Can be used as power supply using .: Yes Protection: reverse polarity of battery (fuse) Output short-circuit overtemperature Operating temperature range: -20 to +50? Humidity (non-condensing): max 98% Housing Material & Color: aluminum (blue RAL 5012) Battery Connection: Screw 13 mm² / AWG6 230 V AC Connection: cable with 1.5 meters long with CEE 7/7 plug Protection: IP22 Weight: 1.3 kg Dimensions (HxWxD): 235 x 108 x 65 mm

Network cable for connecting the control panels

Network cable for connecting the control panels

!!! MINDESTBESTELLMENGE >/= 5 STÜCK !!!VICTRON - Solar Panel 60W-12V Poly 545x668x25mm series 4a

The Victron - Cyrix Li-ct is intended for the connection of a conventional lead-acid starter battery and a consumer battery LiFePO4.The batteries are connected to a delay of 30 seconds when:done an intervention via the CE bus BMSThe voltage at one of the battery terminals to & gt; 13.7 V (27.4 V) ansteigtDie batteries are immediately separated when:takes place off via the CE bus BMSThe battery voltage <13.2 V (26.4 V) fallsContinuous current 120 A and breaking

The digital multi-control panel GX corresponds to its predecessor, but has a new design. Another advantage of this panel lies in the simple assembly: the supplied assembly frame enables the panel to assemble both from front and from behind. The mounting holes are covered by the mounting frame. The housing of the GX panels is made of plastic. This reduces the weight of the panel and it gets a modern look. The panel is suitable for both multis and quattros. It enables the setting of PowerControl and Powerassist electricity limits for two alternating current sources: for example for generator and country power. Settings area: Up to 200 A. The brightness of the LEDs is automatically reduced during the night. Dimensions (HXBXT): 65 x 120 x 40 mm

Power cable for Phoenix smart charger IP43Power Cord with Scghutzkontaktstecker and inlet socket

Mit dem MK3-USB lassen sich folgende Produkte zum Konfigurieren an einen Computer anschließen: Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Wechselrichter (nur Modelle mit einem VE.Bus Kommunikations-Port), ECOmulti, EasySolar, EasyPlus.

Mit diesem Konverter können Zigbee-Daten in ein USB-Signal umgewandelt werden. Er bietet eine einfache Lösung zur Verbindung von Zigbee-basierten Geräten mit Computern oder anderen USB-fähigen Geräten.Technische Daten:- Schnittstelle: Zigbee zu USB- Kabellänge: 1,5 m

Der Zigbee zu RS485 Konverter von Victron Energy ermöglicht die nahtlose Kommunikation zwischen Zigbee-basierten Geräten und RS485-Protokollen. Ideal für die Integration von drahtlosen Kommunikationssystemen in bestehende Victron Systeme.Technische Daten:- Schnittstelle: Zigbee zu RS485- Kabellänge: 1,5 m

-Low voltage-temperature coefficient ensures high efficiency, even at high temperatures.-Außergewöhnliche performance even in low light conditions and high sensitivity to light across the entire solar spectrum.-25 years limited warranty on power output and performance.-2 years limited warranty on materials and workmanship.-Versiegelter, waterproof, multi-functional junction box gives high level of security.High-excursion bypass diodes minimize power drop caused by shading.-The sophisticated E VA (Ethylene Vinyl Acetate) encapsulation system with three-layer back sheet meets the most stringent safety regulations for high-voltage operation.-By A sturdy, anodized aluminum frame allows modules with a number of standard mounting systems can be easily installed on the roof.-The tempered glass of the highest quality, high-transmission tempered glass provides enhanced strength and impact resistance.-Vorverkabeltes quick-connect system with MC4 Steckverbindern. designation: 50W-12 V-Dimensions (LxWxH): 780 × 668 × 30 mm-Weight: 6.1 kg-Nennleistung (P MPP): 90 W-Max. Voltage (V MPP): 19.6 V-Max. Current intensity (I MPP): 4.59 A-Leerlaufspannung (V OC): 24.06 AShort-circuit current (I SC): 5.03 A similar image

Orion-TR Smart isolated DC/DC chargers with a 3-stable batteryada algorithmSuitable for Bluetooth SmartMonitoring, changing the settings and updating the charger at newStanding software functions can be used with any Bluetooth-enabled smartphone, tablet or othersDevice can be carried out.Fully programmable- Batterieladealgorithm (configurable) or firm output.- Intelligent generator compatibility: engine running.Adaptive 3-stage loading algorithm: constant current-constant voltage-preservation• With lead batteries, it is important that the recording time is kept short in flat discharges toAvoid an overload of the battery. After a deep discharge, theConstant voltage duration automatically extended to ensure that the battery is completelyload.• The recording time is fixed for lithium batteries, 2 hours by default.• Alternatively, a fixed output voltage can be selected.Fern-/shutdownA remote-controlled on/off switch or a relay contact can be found on the two-pin connectorconnect.Alternatively, the connection H (right) of the two-pole plug into a battery plus pole or theConnection l (left) of the two-pin connector to the battery minus pole (or for example to the bodyof a vehicle).All models are short -circuit -resistant and can be switched in parallel to increase the output currentwill.Unlimited many devices can be switched in parallel.Over -temperature protectionWith high ambient temperatures, the output current is reduced.Protection class IP43When the screw terminals are installed on the device.Screw terminalsNo special tools are required for installation.Input protection (not interchangeable)Technical specifications:Model: 12/12-30 (360W)Input voltage area (1): 10-17 VSub -voltage shutdown: 7 VSub -voltage restart: 7.5 VStarting stern tension: 12.2VSetting range output voltage: 10-15 VTolerance Output voltage: +/- 0.2 VStarting noise: 2 MV RMSAccount.Maximum output current (10 s) with output stern voltage minus 20%: 40 aShort -circuit output current: 60 aAccount. Output power at 25 ° C: 430 WAccount. Output power at 40 ° C: 360 WEfficiency: 87%Electricity recording without load: <80 MAGalvanic separation: 200 V DC between the entrance, exit and housingOperating temperature range: -20 to +55 ° C (reduction in performance by 3% per ° C above 40 ° C)Air humidity: max. 95%, not condensingDC connection: screw terminalsMaximum cable cross -section: 16 mm² (AWG6)Weight: 1.8 kgDimensions (HXBXT): 130 x 186 x 80 mm(1): If the output voltage is set to nominal or lower than nominal, it remains stable within the specified input voltage area (downward-up function).If the output voltage is set up by a certain percentage higher than the nominal value, the minimum input voltage, in which the output voltage remains stable (not drops), increases by the same percentage.

-Ring temperature-voltage coefficient ensures high efficiency, even at high temperatures.-Then -ordinary performance even in low lighting conditions and high sensitivity to light through the entire sun spectrum.-25 years of limited warranty to power output and performance.-2 years of limited warranty to material and processing.-Sealer, waterproof, multifunctional distribution box offers a high level of security.-High-performance bypass diodes minimize electricity waste caused by shading.-The highly developed E VA (ethylene vinyl acetate) encapsulation system with a three-layer back film corresponds to the strictest safety regulations for high-voltage operation.-With a stable, anodized aluminum frame, the modules with a series of standard assembly systems can be easily attached to the roof.-The securite glass of the highest quality and with a high degree of transmission offers improved strength and bump resistance.Description: 55W-12 V-Meave (LXBXH): 545 × 668 × 25 mm-Weight: 4 kg--Max. Tension (V MPP): 18.8 V-Max. Strong -strong (I MPP): 2.94 a-Leaving voltage (V OC): 22.9 a-Short -end current (I SC): 3.22 aFigure similar

Der Temperaturfühler für die BMV-702 und BMV-712 Serie bietet eine präzise Messung der Batterietemperatur. Durch die Anpassung der Ladeparameter an die Temperatur wird die Batterie geschützt und eine längere Lebensdauer sichergestellt. Technische Daten:Gewicht: 0,05 kgAnschluss: 2-polig, wasserdicht